Vinten Protouch PRO-6 HDV Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 29

Vinten Protouch PRO-6 HDV Скачать руководство пользователя страница 20

20

Optional equipment

Carrying strap

A carrying strap

is available as an optional accessory and is installed as follows:

On the lower moulding of the leg with the strap, drive in the 'knock-out'

using a suit-

able tool. If possible, remove the blank from inside the moulding to prevent subsequent rat-
tle.

Push a blind captive nut

into the hole in the lower moulding.

Using a suitable M5 screw, fully compress the blind captive nut. Remove the M5 screw.

Install a washer

on the lower strap anchor

and screw into the captive nut

. Ensure that the hole in the strap anchor is oriented so that the karabiner

be attached.

On the underside of the tripod bowl

, remove and discard the screw

securing the

corresponding leg clamp

. Do not remove the washer

.

Position the bowl strap anchor

on the leg clamp, ensuring it is correctly oriented. Us-

ing Loctite 221, secure the bowl strap anchor with the 25 mm M6 screw

supplied with

the strap. Tighten screw to a torque of 4.5 Nm (40 lbf in.).

Using the karabiners

, clip the strap

to the strap anchors and adjust to length.

«
...
18
19
20
21
22
...
»

Содержание Protouch PRO-6 HDV






























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды