Vinten 3702 Скачать руководство пользователя страница 44

Страница: 44 / 84

14.6 Referring to

, fit steering chain (23) and joining link (24).

14.7 Slacken clamp bolt (26).

14.8 Ascertain wheel position (set of wheels under change-over gear).

14.9 Align steering ring indicators to the wheel position.

14.10 Tighten clamping bolt (26).

14.11 Referring to

Fig 6.14

, refit change-over gear cover (9).

Column bearings

To install column bearings:

15.1 Before refitting column bearings to a tube set all the adjustable bearings on that tube to minimum
setting.

15.2 Fit bearing assembly into place and secure with four countersunk socket headed screws.

15.3 Adjust bearings

(Section 4)

Other replacements

All other replacements are simple and the method is self-evident after a brief study of the particular item

and the exploded drawing in

Section 6

. Replacements affecting wheels or steering chains are equally simple

but require a check on tracking and chain tensioning

(Section 4)

NOTE:

When fitting a crab/steer pin circlip, shim as necessary to allow 1/32in. clearance between
circlip and clutch body.
If the steering change-over gear

(Fig 6.10)

has been dismantled, secure items (48) and (50)

with Loctite 221 during assembly.

Содержание 3702





















































































Результаты поиска

Содержание 3702

Отзывы:

Похожие инструкции для 3702

Бренды по названию

Популярные бренды

Vinten 3702, Руководство по обслуживанию

Результаты поиска

Содержание 3702

Отзывы:

Похожие инструкции для 3702

Бренды по названию

Популярные бренды