MADE IN CHINA
Car Jump Starter VIKING ZULU14 14100mAh
Thank you for choosing our air purifier VIKING. Please read the instruc�on before the first use.
User manual:
1) LED lamp
2) 13.5V/1A charging input socket
3) USB output: 5V/2A
4) USB output: 5V/2A
5) Power switch
6) Safety hammer
7) Compass
8) LED control switch
9) LCD screen
10) jump start socket
Using the Torch
1 .Slide the ON/OFF switch to ON. To turn the torch ON and OFF, Long press light control switch for 3 seconds
2.There are 3 models, normal.strobe and SOS. Pressing the switch bu�on lightly once the light is on will scroll through each mode.
Notes: Please slide the ON/OFF switch to "OFF* if do not use it.
Contents:
jump starter *1
3 in 1 mobile cable 1
13.5V Charger *1/ Car charger (op�onal)
jumper cable *1
user manual *1
Technical specifica�ons:
USB-A:
2x 5V / 2A max.
DC jack 5.5 / 2.1mm:
12V, 16V, 19V / 3.5A max.
Star�ng current:
12V / 300A max.
Peak output current:
600A
Charging �me:
12V, 3-4h
Charging current:
DC 13.5V / 1A
Min. number of charges:
3000x
Size:
199 * 62 * 46mm
Working temperature:
0-60o
C
Star�ng a car with the jump starter
Warnings
1 .When using the Jump Starter make sure the blue plug is FIRMLY inserted into the Jump Starter. IF NOT, the jump starter will not start your car AND this may cause damage to the jump
starter.
2. Make sure the ba�ery clamps make good clean contact with the ba�ery terminals. IF the jump starter fails to start your car a�er 3 a�empts,stop and check for other possible problems.
3. Remove the clamps from the ba�ery terminal within 30 seconds a�er star�ng your car. Failure to do so may damage the jump starter.
4. DO NOT connect the two ba�ery clamps together. Doing so is not only dangerous but will also damagethejump starterand void your warranty.
5. Make sure the jump starter has over 80% power when using to star�ng the car.
•
Don't let the product get wet
•
Can't put product in water
•
Do not use products under dangerous condi�ons
•
Products should not be placed at temperatures exceeding 70 degrees Celsius.
•
Products should not be exposed to heat sources.
•
Only use the matching charger to charge.
•
Under extreme condi�ons, leaks may occur in ba�eries. Use a cloth to wipe carefully. Avoid contact with skin. If contact with skin or eyes, use clear water immediately. Rinse and see a
doctor in the hospital.
•
A�er the end of ba�ery life, the ba�ery should be treated environmentally
What is Covered
This warranty covers any defects in materials or workmanship with
the excep�ons stated below.
What is Not Covered
This warranty does not cover damage or product failure resul�ng from
normal wear and tear.physical abuse,improper use.
FAQ
Q:How many �mes can the jump starter charge a mobile phone?
A:From a full charge the jump starter will charge a mobile phone about 4-5 �mes(tests done on an Iphone 6 1810mAh)
Q:How long will the jump startertake to charge a mobile phone?
A:Approximately 2 hours depending on the phone.
Q:How many �mes can the jump starter start a car from FULL charge?
A:Approximately 15-20 �mes.
Q:How long will the ba�ery stay charged if le� idle?
A:4-6 months. HOWEVER we suggest recharging every 3months.
VIKING products are distributed and serviced by:
BONA SPES s.r.o.
Řepčín 250, Olomouc 77900, Czechia
VAT No.: 3476774
+420 777 109 009
www.best-power.cz, [email protected]
1. Connect the Jumper Cables to the Jump Starter by plugging the connector into the
Jump Starter Socket. Make sure the blue plug is FIRMLY inserted into the jump starter.
2. Connect the RED Ba�ery Clamp to the Posi�ve( + ) ba�ery terminal and connect the
BLACK Ba�ery Clamp to the Nega�ve(-) ba�ery terminal. Make sure the ba�ery clamps
make good clean contact with the ba�ery terminals.
3. Slide the Jump Starter ON/OFF switch to the ON posi�on.
4. Start the car.
5. Once the car has started, remove the jumper cables from the ba�ery WITHIN 30
seconds (failure to do so many damage the jump starter) and leave the engine running.
návod na obsluhu
user manual
