manualshive.com logo in svg

Viking VFR400, Руководство пользователя

Поделиться
Скачать
Viking VFR400 Скачать руководство пользователя страница 9

9

VFR-400 • 5403548 • REV W • 8/17

CIRCUIT PARAMETERS

All voltages regulated DC  

 

 

 

 

 

 

 

 

 

 

 

Initiating Device Zones

 For connection of dry contact initiating devices and compatible 2 wire smoke detectors.  (All values nominal)

• 4 Class B (Class A module available)*

• Power limited, current limited to protect 2 wire smoke detectors

• Maximum 2 wire 24VDC smoke detector load per zone - 2.5 ma (Use only detectors that are listed in compatibility list.)

• Maximum Line resistance - 100 ohms (Except linear heat detection cable, 700 ohms per zone)

• End-of-Line Resistance - 5.1K ohms

• Normal standby current - approximately 4.0 mA

• Standby voltage - 25VDC maximum, 13.4 minimum

• Maximum short circuit current - approximately 36mA

• Maximum Impedance for Alarm - 1400 ohms

• Normal supervisory current - approximately 4mA

• Low current trouble activation - approximately 3.3mA

• Alarm activation current - approximately 10mA

• Ripple voltage - .4 VDC

• Maximum operating voltage range: 22.5 - 25.9V DC 

 

 

 

 

 

 

 

 

• Frequency - continuous 

 

 

 

 

 

 

 

 

 

 

* In programs 6-9, Zone 1 is a normally closed zone for Firecycle

®

 Detectors

Dedicated Supervisory Zones

• For dry contact supervisory devices such as tamper, low air, or high air switches

• 2 Class B circuit, latching or non-latching

• Power limited, current limited

• End-of-Line resistance - 5.1K ohms

• Ripple Voltage - .1 VDC

• Frequency - continuous

• Maximum voltage - 25VDC   

 

 

 

 

 

 

 

 

 

 

• Maximum short circuit current - approximately 36mA

• Maximum line resistance - 100 ohms

• Normal supervisory current - approximately 4mA

• Low current trouble activation - approximately 3.3mA

• Supervisory current condition - approximately 10mA

(Does not include power for any auxiliary devices)

Notification/Release Circuits

The indicating circuits of the VFR-400 are Non-coded. This allows the use of visual and audible appliances on the same circuit.  

If temporal notification appliances are required for evacuation, selectable tone appliances shall be used.

The notification outputs do not provide synchronization. The notification appliances shall be compatible with the sync module 

selected.  The sync module shall be installed as per manufacturers instructions. Synchronization is limited to only one circuit and 

not between circuits. Systems intended for the release of Halon 1301 as described in NFPA 12A, or clean agents as described in 

NFPA 2001, shall have provision for a pre-discharge notification circuit. If the signal is required to be separate and/or distinct 

from the evacuation signal, two notification circuits are required.  One shall be programmed as FIRST ALARM. It will provide 

a steady output upon activation of any initiating zone programmed as an alarm zone. This is the evacuation signal. If a temporal 

signal is required, notification appliances that can produce a temporal tone shall be used. This allows the use of strobes and horns 

on the same circuit. The other notification circuit shall be programmed as SECOND ALARM. It will provide a steady output upon 

activation of a second initiating zone programmed as an alarm zone. This is when the pre-discharge timer would start and would 

be the pre-discharge signal. If a temporal or other type of signal is required, notification appliances shall be used. This allows the 

use of strobes and horns on the same circuit. If a separate signal for discharge were required, a third notification circuit would be 

used that would be programmed to operate whenever the release circuit is activated.  

Zones programmed as MANUAL RELEASE will activate outputs programmed as SECOND ALARM, even if the MANUAL 

RELEASE zone is the first alarm zone activated. SECOND ALARM is intended to be used as a pre-discharge signal for cross 

zone applications. Refer to page 60 for a complete description of first and second alarm requirements and operation.

      • 4 Class B (Class A module available for notification)

Содержание VFR400




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды