manualshive.com logo in svg

Viking Quiet Cool VCRB5301, Руководство по обслуживанию, Страница: 34 / 47

Поделиться
Скачать
Viking Quiet Cool VCRB5301 Скачать руководство пользователя страница 34

Service Procedures

34

©2012 Viking Preferred Service

3. Shorted Thermistor Alarm

The controller will sense an shorted thermistor 

condition within 15 seconds of power on.

Shorted Refrigerator Thermistor Alarm

When the control senses that the refrigerator 

thermistor is shorted, "Shr" is displayed on the 

control along with the zone, "REFRIGERATOR". 

You also receive an audible alarm consisting of five 

beeps that occurs only one time. The visual alarms 

as described above will continue until the condition 

is corrected.

The unit will continue to execute temperature control 
and defrost operations as required until the condition 

is corrected. The control does this through software 

programming, acting as if the cut-out temperature 

is never reached in the faulty zone, temperature 

control in the other zone is unaffected.

The visual alarms will reset by themselves within 

15 seconds of the open thermistor condition being 

corrected and temperature control reverts back to 

normal operation.

4. Power Loss Alarm

If the control experiences a power loss condition 

and power is restored, the Power Loss alarm is 

displayed. This consists of the "POWER" indicator 

being flashed on and off along with the temperature 

digits flashing on and off. All other indicators will be 

off and only "ACTIVATE CONTROLS and ALARM 

OFF keys are active on the control panel.
There is no audible alarm indication associated 

with the power loss alarm. Pressing and releasing 

the "ALARM OFF" pad will result in "POWER" 

indicator extinguishing and the temperature digits 

revert back to normal temperature display.

5. Door Open Alarm

If the control senses that a door is open for a period 

of time, equal to the door open delay (factory default 

is 3 minutes, this time can be adjusted in service 

mode B) a continuous audible alarm will sound. 

At the same time "DOOR OPEN" illuminates on 

LED display and will remain on until condition is 

corrected.
Press the "ALARM OFF" pad and the audible alarm 

will cease. Pressing and holding the "ALARM OFF" 

pad for three seconds will disable the audible door 

alarm, until the "ALARM OFF" pad is again held for 

three seconds which will enable the audible door 

alarm once again.
These actions will not clear the visual "DOOR" 

alarm, that can only be cleared by shutting the 

doors and allowing the control to reset it.

Содержание Quiet Cool VCRB5301
















































Отзывы:

Нет отзывов