Viking Quiet Cool VCRB5301 Скачать руководство пользователя

Страница: 29 / 47

Service Procedures

ALARM

OFF

HIGHER

LOWER

While in Mode B, press and

release "ALARM OFF" one time,

this will result in "DOOR OPEN"

illuminating on the display along

with the current numeric value in minutes that

the delay is set at. Factory default for this

adjustment is 3 minutes. Range is 1 to 20

minutes in 1 minute increments.

The duration is adjusted using the

"HIGHER and LOWER" pads.

Adjust Door Open Alarm delay

Adjust Compressor Dwell Time

This adjustment is not a field adjustment and

should not be performed by technicians. This

is a factory only adjustment.

If you see "Cdt" in the display, immediately

exit Mode B by holding "ACTIVATE

CONTROLS" for three seconds until you get

three audible beeps. Return to your previous

actions.

Adjust Compressor High Frequency

This adjustment is not a field adjustment and

should not be performed by technicians. This

is a factory only adjustment.

If you see "CHF" in the display, immediately

exit Mode B by holding "ACTIVATE

CONTROLS" for three seconds until you get

three audible beeps. Return to your previous

actions.

Adjust DC Fan Cycling On Time

Adjust DC Fan Cycling Off Time

This adjustment is not a field adjustment and

should not be performed by technicians. This

is a factory only adjustment.

If you see "dCo" in the display, immediately

exit Mode B by holding "ACTIVATE

CONTROLS" for three seconds until you get

three audible beeps. Return to your previous

actions.

This adjustment is not a field adjustment and

should not be performed by technicians. This

is a factory only adjustment.

If you see "dCF" in the display, immediately

exit Mode B by holding "ACTIVATE

CONTROLS" for three seconds until you get

three audible beeps. Return to your previous

actions.

Содержание Quiet Cool VCRB5301
















































Результаты поиска

Содержание Quiet Cool VCRB5301

Отзывы:

Похожие инструкции для Quiet Cool VCRB5301

Бренды по названию

Популярные бренды

Viking Quiet Cool VCRB5301, Руководство по обслуживанию

Результаты поиска

Содержание Quiet Cool VCRB5301

Отзывы:

Похожие инструкции для Quiet Cool VCRB5301

Бренды по названию

Популярные бренды