Viking Quiet Cool VCRB5301 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 47

Viking Quiet Cool VCRB5301 Скачать руководство пользователя страница 19

To avoid risk of electrical shock, personal injury, or death, disconnect electrical power source to unit, unless test

procedures require power to be connected. Discharge capacitor through a resistor before attempting to service.

Ensure all ground wires are connected before certifying unit as repaired and/or operational.

WARNING

!

Disassembly

©2012 Viking Preferred Service

19

Inverter (continued)

4. The inverter is now accessible on the right

side.

Inverter

120 VAC is supplied to the inverter

from E4 on the High Voltage Board.

The LV board sends 5 VDC to the

inverter to operate the compressor.

5. Reverse procedure to reinstall.

1. To access the condenser fan assembly,

remove upper air grill assembly, remove

control panel assembly (see Air Grill and

Control Panel Removal sections, Page

Condenser Fan

The condenser fan is located in the upper

machine compartment of the unit. 120 VDC

is supplied to the fan when the Compressor/

Condenser Fan relay closes to E4 on the

High Voltage Board.

2. Remove the control box in order to gain

easy access to the door hinge area for

service. There are 4 ¼” hex screws (2

on each side) holding the control box to

the refrigerator housing. Remove these

screws.

3. Unplug the 15-pin Molex power plug, as

well as the 2-wire converter frequency

cable and the 3-wire thermistor plug .

Remove electronics box and set aside to

gain access to condenser fan assembly.

Condenser Fan

4. Remove the three 1/4" hex screws

holding fan assembly in place, remove

fan assembly

«
...
17
18
19
20
21
...
»

Содержание Quiet Cool VCRB5301
















































Отзывы:

Нет отзывов