background image

1 of 18

I.

Instruction

Thank you for choosing this product. If you want to know more about this product beyond the user manual, please visit our website
or contact with our sales.

Before use this product, please read this statement carefully. Once used, this statement will be deemed to have been fully accepted
and accepted internally. Please strictly comply with the user manual to install and operate this product. Viewpro will not be liable
for any damage or damage caused by improper installation and use of the product.

Safety Caution
1) When this product works, the high-speed rotation of the propeller will bring different degrees of damage and damage to

people and articles. Therefore, when you use this product, please do not use it in places with many people or complicated
environment.

2) Please abide by local laws and regulations when using any products of our company.
3) Before use, please read the operation manual carefully and watch the video of the aircraft operation process. Our company

will not be liable for any loss caused by violation of the relevant operation process.

4) Do not modify the parameters of the remote control. When it is used, the remote control must be turned on before the

aircraft is powered on. When power is cut off, the remote control must be turned off before the aircraft is powered off.

5) Do not overcharge or put the battery long time with full or low capacity. The two connectors should be connected to the

charger at the same time to charge the battery. The red light is always on during charging, and the green light is on after
charging;The storage voltage of a single battery is controlled at about 3.85V, the total voltage of a 3S battery is controlled at
about 11.55V, the total voltage of a 4S battery is controlled at about 15.4V, and the total voltage of a 6S battery is controlled
at about 23.1V.

6) Before the flight mission, please confirm the battery voltage;
7) Keep away from unsafe factors, such as obstacles, people, children, buildings, high-voltage lines, trees, etc.
8) Do not get close to or touch the rotating motor or propeller to avoid being cut by the rotating propeller.
9) Be sure to fly under the safe take-off weight in case of danger.
10) Before flight, please check whether the propeller and arm are properly installed and firmly.
11) When using the ground station to operate the UAV, the captain and pilot should have relevant operating qualifications.
The operator must have relevant experience in aircraft operation.Novices must be trained in simulators to operate the training
machine after they have mastered the simulated aircraft.

Содержание Blue Shark F250



















Отзывы: