View Sky Sensor Скачать руководство пользователя страница 1

Страница: 1 / 12

1 of 12

Installation Guide

QDM-05-000045

Rev 8 | July 2022

2022 View, Inc.

Sky Sensor Installation Guide

Work Performed By:

Low-Voltage Electrician

Sky Sensor Body

Sky Sensor Base

The roof-mounted Sky Sensor

provides external light level data

and infrared temperature data to the

View system to allow optimization

of tint levels for each zone. The

assembly includes the Sky Sensor

with a 4 ft. length of CAT5 Ethernet

cable attached.

Package Includes

1. Sky Sensor Assembly

•

View Net (P/N: VN-SKY)

•

CSS (P/N: 005-101418)

2. Sky Sensor Installation Kit (P/N: VN-SMK)

Tools and Materials Required

3/4” Rigid Metallic Tubing (RMT) for roof mast, brackets, flashing and sealant.

#2 Phillips screwdriver

3. Cutting, Drilling and Deburring tools.
4.

Wire stripping tools.

Wrenches.

6. Grounding wire: 12 AWG THHN green or green/yellow
7.

300 ft Unshielded Plenum CAT5 ethernet cable spool, modular connectors and crimping tool.

8. Standard Junction box (10 x 10 x 6”), CSS Only
9.

CAT5 Ethernet tester

Additional Supporting Documentation

Sky Sensor Data Sheet - QDM-02-000247

CP5.5 Data Sheet - QDM-02-000244

CP5.0 Data Sheet - QDM-02-000219

CP2.0 Data Sheet - QDM-02-000033

Содержание Sky Sensor











Результаты поиска

Содержание Sky Sensor

Отзывы:

View Sky Sensor, Руководство по установке, Страница: 1 / 12

Результаты поиска

Содержание Sky Sensor

Отзывы: