background image

6

Please dispose of packaging waste in line with statu-
tory regulations.

DE:

Use the disposal system organised by
Viessmann.

AT:

Use the ARA statutory disposal system (Altstoff
Recycling Austria AG, licence number 5766).

CH:

Packaging waste is disposed of by the HVAC
contractor.

Symbols

Symbol

Meaning

Reference to other document containing
further information
 

1.

Step in a diagram:
The numbers correspond to the order in
which the steps are carried out.

Warning of material losses and environ-
mental pollution
 
 
Live electrical area
 
 
Pay particular attention.
 
 

Component must audibly click into place.
or

Acoustic signal

Fit new component.
or

In conjunction with a tool: Clean the sur-
face.

Dispose of component correctly.
 
 
Dispose of component at a suitable collec-
tion point. Do 

not

 dispose of component in

domestic waste.
 

The steps in connection with commissioning, inspec-
tion and maintenance are found in the "Commission-
ing, inspection and maintenance" section and identified
as follows:

Symbol

Meaning

Steps required during commissioning

Not required during commissioning

Steps required during inspection

Not required during inspection

Steps required during maintenance

Not required during maintenance

Intended use

The appliance is only intended to be installed and
operated in sealed unvented heating systems that
comply with EN 12828, with due attention paid to the
associated installation, service and operating instruc-
tions.

Depending on the version, the appliance can only be
used for the following purposes:

Central heating

Central cooling

DHW heating

Information

Disposal of packaging

5692878

Information

Содержание Vitocal 350-A AWHI 351.A14













































































































































Отзывы: