Viega LLC
585 Interlocken Blvd.
Broomfield, CO 80021
Phone (800) 976-9819
www.viega.us
Product Instructions
Viega PureFlow Press
Zero Lead Bronze Fittings
PI-PF 520740 0621 PureFlow Press Zero Lead Bronze (EN ES FR)
EN
Product Instructions
Viega PureFlow Press Zero Lead
Bronze Fittings
This document is subject to updates. For the most current Viega
technical literature please visit www.viega.us.
Pure
Flow
1/2”
Pure
Flow
1/2”
6
Pure
Flow
1/2”
1
6
7
2
8
10
3
9
11
4
5
EN
Viega PureFlow Press
Zero Lead Bronze Fittings
Viega products are designed to be
installed by licensed and trained plumbing
and mechanical professionals who are
familiar with Viega products and their installation.
Installation by non-professionals may void
Viega LLC’s warranty.
The tool locator ring must be in the factory
installed position while making a press to
ensure a consistent leakproof connection.
It may be necessary to rotate the tool locator ring
to avoid interference between the ring and tool.
The tool locator ring must be in the factory
installed position while making a press to
ensure a consistent leakproof connection.
It may be necessary to rotate the tool locator ring
to avoid interference between the ring and tool.
Zero Lead identifies Viega
®
products meeting
the lead free requirements of NSF 61-G
through testing under NSF/ANSI 372 (0.25%
or less maximum weighted average lead content).
1
Square off tubing to proper length. Uneven,
jagged, or irregular cuts will produce unsatisfactory
connections.
2
Insert PureFlow Press fitting with attached sleeve
into tubing and engage fully.
3
Ensure full tubing insertion at view holes in
attached press sleeve. Full insertion means tubing
must be completely visible in at least two view
holes and partially visible in the one.
If using a hand tool continue with steps 4 to 7. If
using a power tool continue with steps 8 to 11.
4
Position the PureFlow press tool perpendicular
over the press sleeve, resting it against the tool
locator ring. Make sure the PureFlow press tool is
properly aligned (see step 6 figure if it is not).
5
Close handles, using trigger to reduce grip span if
desired.
6
If the PureFlow press tool is not properly aligned
with the locator ring, use the emergency release
(using a screw driver to turn the emergency
release) to open the press tool. Once released,
align the PureFlow press tool properly and go
back to step 4.
WARNING!
The connection is not leakproof when
the tool has been opened by emergency
release. The tool locator ring must be present to
ensure a proper PureFlow Press connection.
7
Extend the PureFlow press tool handle and
continue ratcheting until automatic tool release
occurs at the proper compression force.
8
If using a power tool, insert the appropriate
PureFlow Press Jaw into the press tool and push
in the holding pin until it locks.
9
Open jaw and position perpendicular over press
sleeve resting it against the tool locator ring.
CAUTION!
Do not press twice.
CAUTION!
Do not press twice.
10
Start the pressing process; hold the trigger until
the jaw has automatically released.
11
When press connection is complete, open and
remove the jaw.
WARNING!
The tool locator ring must be present
to ensure a proper PureFlow Press
connection.
ES
Instrucciones del producto
Accesorios Viega PureFlow Press
de bronce Zero Lead
Este documento está sujeto a actualizaciones. Para obtener la
documentación técnica más reciente de Viega, visite www.viega.us.
FR
Instructions produit
Raccords en bronze Viega PureFlow
Press Zero Lead
Le présent document est soumis à des mises à jour. Pour consulter les
manuels techniques Viega les plus récents, veuillez visiter www.viega.us.
