manualshive.com logo in svg

Victron energy battery protect BP 100, Руководство пользователя, Страница: 13 / 15

Поделиться
Скачать
Victron energy battery protect BP 100 Скачать руководство пользователя страница 13

4.2.2. Programming table

Programming table for BatteryProtect 12/24V

7-segment display

Under voltage shutdown 12V/24V system

Under voltage restart 12V/24V system

0

10.5V/21.0V

12.0V/24.0V

1

10.0V/20.0V

11.5V/23.0V

2

9.5V/19.0V

11.5V/23.0V

3

11.25V/22.5V

13.25V/26.5V

4

11.5V/23.0V

13.8V/27.6V

5

10.5V/21.0V

12.8V/25.6V

6

11.5V/23.0V

12.8V/25.6V

7

11.8V/23.6V

12.8V/25.6V

8

12.0V/24.0V

13.0V/26.0V

9

10.0V/20.0V

13.2V/26.4V

A

Buzzer or LED mode

b

Relay mode

C

Lithium mode

d

Detect system voltage

4.3. Status indicator

The decimal point of the 7-segment display is used for status indication:

• Illuminated: the BatteryProtect is attempting to activate the output.

• Flash every 5 seconds: output is active.

• Flash every 2 seconds whilst in Li-ion mode: output ‘connecting’. When in Li-ion mode the SBP will observe a dead period of 30

seconds after the remote input of the BP has become free floating.

4.4. Remote control and short circuit behavior

This section describes the behaviour of the BatteryProtect when it is controlled via the remote on/off input and when a short circuit
has been detected.

• The BatteryProtect will connect the load 1 second after the remote input is closed.

• The BatteryProtect will disconnect the load immediately when the remote input is opened.

• When in Li-ion mode the BP will connect the load 30 seconds after the remote input of the BP has been pulled high by the

BMS. This delay increases to 3 minutes in case of frequent switching.

• In case of a short circuit, the BatteryProtect will attempt to connect the load every 5 seconds. After two attempts the display will

show E1 (short circuit detected).

4.5. Error & Warning modes

There are 4 possible error modes, indicated by the 7-segment display:

• E1 Short circuit

• E2 Over temperature / P2 Over temperature warning

• E3 Under voltage / P3 Under voltage warning

• E4 Over voltage

After 5 minutes the error is no longer displayed to reduce current consumption.

Please refer to the appendix chapter 

Error and Warning codes [13]

 for more info on each error.

BatteryProtect 12/24V

Page 11

Operation and programming

Содержание battery protect BP 100
















Отзывы:

Нет отзывов