1. Press the power button to turn on the bait box.
2. Wait for confirmation of connectivity.
3
BATTERY INSTALLATION
DOWNLOAD THE APP
CALIBRATION
2. Insert 4 AA alkaline batteries (provided).
3. Replace the battery compartment lid using the screws provided.
These instructions appear step-by-step on the VLINK™ mobile app.
1. Download the VLINK™ app from the Apple or Google Play Store.
Box Lid
START-UP GUIDE
Victor
®
VLINK
™
Bait Box Model: V440
FCC:
this device complies with part 15 of the fcc rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this device not expressly approved by
WoodstreamCorporation could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC:
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause interference; and (2) This device must accept
any interference, including interference that may cause undesired operation of the device.
RF Exposure:
This equipment complies with FCC and IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body.
Manufactured for:
Woodstream Corporation
69 N. Locust Street, Lititz, PA 17543
•
800-800-1819
1. Open box lid and remove the screws on the battery
compartment using a Phillips head screwdriver.
2. Launch the app and follow the on-screen instructions to connect
your trap to the app.
Battery
Compartment
Bait Post
LED Light
Power Button
Calibration
Button
QR Code
Key
3. Ensure the bait box is sitting on the ground/surface of the exact
location for which you are deploying.
4. Press and hold the calibrate button for 2-4 seconds. Once a solid
yellow LED light is displayed, ensure the bait posts are empty and
close the lid.
5. Upon closing the lid, a yellow LED on the top of the box will start
blinking and will begin to blink faster as calibration progresses.
When complete, the yellow LED will turn off and a green LED will
turn on.
6. Open the lid and bait the box. Place the bait in the two bait
positions and close the lid tightly.
7. Upon closing the lid, a green LED on the top of the box will start
blinking and will begin to blink faster as calibration progresses.
When complete, the green LED will turn off and your bait box will
be ready.
DOCUMENTATION
SERVICING THE BAIT BOX
1. Select the type of bait, quantity, and add notes
into the app.
1. Once a notification is received and service is required,
re-calibration will be necessary.
2. If necessary, remove any remaining bait on the bait posts.
3. Open the bait box and scan the device QR code.
4. Select the 'Re-Calibrate' button in the app.
5. Follow the above calibration instructions or follow the prompts
within the mobile app.
LED Guide:
• A green LED light will flash to indicate the device is
powering on
• A blue LED light indicates connection is successful
• Three short blinks of a red LED light indicates the bait box is
powering down due to connection failure or from holding
down the power button
• Three long blinks of a red LED light indicates failure during
calibration
• Quick blinks of red LED light every four seconds indicate the
bait box is powered off, but batteries are installed
• Upon pressing the power button, one blink of red LED light
following three blinks of green LED light indicates the bait
box is powered on but battery level is below 10%
