background image

 

UG:402 

Page 1

PMBus Interface and Accessories 

User Guide 

USER GUIDE  |  UG:402 

Introduction 

The PMBus™-USB Adapter (I2C-ADAPTER-A00) allows users to communicate with PMBus-version Vicor 
power modules through the signal pins. A PMBus control interface is provided for digital management 
and access to telemetry monitoring offered by the product. The PMBus to USB Adapter converts the 
PMBus to USB communication protocol by an internal isolated controller that allows users to easily 
connect to a host PC (no driver installation required on Windows). A GUI, available for download on the 
Vicor website, is provided for users to easily monitor and control the power module.

The PMBus interface of a VIA

, a dedicated Digital Supervisor or Point-of-Load Isolator is used for 

communication purposes with the provided GUI installed on the user’s PC. 

The PMBus interface of a VIA, Digital Supervisor or PLI allows users to read and write into the status 
configuration registers of the module, monitor faults and obtain other additional device information. 
The PMBus-USB adapter provides the ability to demonstrate the PMBus digital interface offered on 
select Vicor products in an evaluation environment. 

Contents Page

Jon Siegers
Ankur Patel
Applications Engineering

Introduction  

1

Connector Information - 
PMBus™-USB Adapter 

3

Application Details 

4

Features 4

VIA to Adapter Bridge Board  5

GUI Configuration 

8

Содержание PowerBench PMBus










Отзывы: