background image

Preface

4

Preface

Target group of this 

manual

This manual is intended for professional agrarians and other people
trained in working in the field of agriculture, who are competent to
operate this machine, as required by national legislation, and who
have knowledge of assembly activities.

For your safety

Ensure that you are familiar with the contents of this manual before
you start using or assembling the implement. This will ensure that you
obtain an optimum result and are working safely.

See section »Safety regulations« on page 10.

Should you have any questions or if anything is unclear, please
contact the manufacturer.
Ensure that this manual is available to all persons who will be working
with this machine. In this way, you will:

prevent accidents,

respect the warranty conditions,

always have a machine in perfect working order.

For the employer

All personnel who operate this machine must be authorised to do 
so according to the applicable national legislation.

All personnel are to be trained in the use of the machine regularly 
(at least once a year) in accordance with employers’ liability 
insurance association guidelines. Untrained or unauthorised 
individuals are not permitted to use the machinery.

You are responsible for the safe operation and maintenance of 
your machine. You must ensure that you and anyone else who is 
going to operate, maintain or work around the unit be familiar with 
the operating and maintenance procedures and related safety 
instructions as mentioned in this manual.

You are responsible for providing personal protective gear to 
personnel who use the machine or who are performing 
maintenance or repairs on it. This includes: safety goggles, safety 
shoes, safety gloves, etc.

Содержание RO-M EW


































































































































































































































Отзывы: