manualshive.com logo in svg

VibroSystM DMV-100, Руководство по установке

Поделиться
Скачать
VibroSystM DMV-100 Скачать руководство пользователя страница 38

38

DMV-100 Rotor Creep and Speed Detector - Installation Manual

The relay switches as follows:

Table 3: Relay status according to event

Event Reported

Relay Status

Both LEDs inactive - main rack-mount unit powered-off

relay de-energized

Sensor and/or cable not connected

Red “ROTATION” LED active - rotation reported

Green “STOP” LED active - no rotation reported for more than 25 seconds

relay energized

5.3.5 Connecting 4-20 mA Output (RPM) Terminals

This 3-position connector delivers an analog RPM signal, which corresponds to the displayed reading. 

Figure 35 : RPM output (4-20 mA) connector assignment

Note 

:This output signal will drive a maximum resistive load of 500 

.

To make use of this linear output, available to a controller or other third-party metering equipment, 
apply the following transfer formula: 

RPM  =  Linear Output (mA)  X  Max(RPM) – Min(RPM) +  5 Min(RPM) – Max(RPM)

16 4 

4 

where: 

Min(RPM) =  lower RPM limit as configured into the Speed Indicator

Max(RPM) =  upper RPM limit as configured into the Speed Indicator

Linear Output (mA) =

reading at 4-20 mA output terminals
(see parameters

 LSet.L

 and 

LSet.H

 in Section 

5.4.2.1 “Parameters”

)

Содержание DMV-100





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды