Viavi CellAdvisor 5G Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 359

Viavi CellAdvisor 5G Скачать руководство пользователя страница 111

99

Using LTE/LTE-A FDD Analyzer

Introduction

The CellAdvisor 5G LTE/LTE-A FDD Analyzer is the optimal portable test solution for installation and maintenance of cellular base
stations and cell sites, running with external AC power or battery for the field. Its touch-based user interface has been specifically
designed with customized menus and simple calibration procedures, providing service providers with accurate and reliable
LTE/LTE-A FDD measurement results.

The CellAdvisor 5G is the optimal solution to perform following measurements:

■

Spectrum Analysis

▪

Spectrum

■

RF Analysis

▪

Channel Power

▪

Occupied Bandwidth

▪

Spectrum Emission Mask

▪

ACLR

▪

Multi-ACLR

▪

Spurious Emissions

■

Power vs Time

▪

Power vs Time (Frame)

■

Modulation Analysis

▪

Constellation

▪

Data Channel

▪

Control Channel

▪

Subframe

▪

Frame

▪

Time Alignment Error

▪

Data Allocation Map

▪

Carrier Aggregation

■

OTA Analysis

▪

OTA Channel Scanner

▪

OTA ID Scanner

▪

OTA Multipath Profile

▪

OTA Control Channel

«
...
109
110
111
112
113
...
»

Содержание CellAdvisor 5G








































































































































































































































































































































































Отзывы:

Нет отзывов