Viavi CellAdvisor 5G Скачать руководство пользователя страница 347

Страница: 347 / 359

CellAdvisor 5G User's Guide

335

Setting measure setup

Tap the

Setup

(

)icon on the side bar of each measurement mode.

To set the CPRI line bit rate, tap

Link Rate

under

Port Configuration

and select the CPRI link rate option from

614.4 Mbps

1228.8 Mbps

2457.6 Mbps

3072.0 Mbps

4915.2 Mbps

6144.0 Mbps

9830.4

Mbps

10137.6 Mbps

NOTE:

It is important that you set the link rate correctly to avoid any misleading LOS and LOF alarms displayed on the
screen.

To turn on or off the through mode, tap

Off

Thru

line.

To set the Tx Clock, tap

Recovered

(default) in

Clock

box.

Содержание CellAdvisor 5G








































































































































































































































































































































































Результаты поиска

Содержание CellAdvisor 5G

Отзывы:

Viavi CellAdvisor 5G, Руководство пользователя, Страница: 347 / 359

Результаты поиска

Содержание CellAdvisor 5G

Отзывы: