Viavi CellAdvisor 5G Скачать руководство пользователя страница 26

Страница: 26 / 359

Getting Started

Side panel view (right)

No.

Description

MicroSD

port: You can use this port to insert your Micro SD card to save measurement data of the instrument.

LAN

port: You can use this Ethernet communication port to connect your instrument.

Mini USB

port: You can use this USB client port to connect and control your instrument. It supports USB TMC and

controls via SCPI communication.

AC/DC Adapter

port: This port is to supply power via AC/DC power adapter provided with your instrument.

NOTE:

You need to open the led located between the cooling fans on the right side panel to use ports.

Installing battery

You need to install the Lithium Ion battery pack provided with your instrument. Follow the instruction to install batteries.

Installing battery

Lay the unit on the back side with the LCD facing up.

Unscrew the battery door thumb screw and slide the battery door off.

Slide a battery straight in keeping care to have the key feature on the back side of the battery.

A user will feel the battery contacts engage the battery.

Содержание CellAdvisor 5G








































































































































































































































































































































































Результаты поиска

Содержание CellAdvisor 5G

Отзывы:

Viavi CellAdvisor 5G, Руководство пользователя, Страница: 26 / 359

Результаты поиска

Содержание CellAdvisor 5G

Отзывы: