Viavi 87339 Скачать руководство пользователя

Страница: 190 / 198

G - 1

Appendix G - Connecting Dual Antenna Coupler Kit

GPSG Dual Antenna Coupler Kit Connection

STEP

PROCEDURE

Connect Coaxial Cable (TNC) (50 ft) (supplied with the GPSG-1000) between the

GPS TX COUPLER Connector and the GPSG Splitter Common Port.

Connect two Coaxial Cables (TNC) (12 ft) between the GPSG Splitter and two

GPSG-1000 Antenna Couplers.

(Use the GPSG-1000 Antenna Coupler and Shot Bag supplied with the GPSG-

1000.)

Ensure the Connector Termination is in place on the open GPSG Splitter

connector.

For Coupler Loss and Cable Loss values to enter in the GPSG-1000 I/O setup

screen; calculate the average insertion loss of the couplers being used. Add to

this value 9.5 dB for the splitter/combiner and enter this value as coupler loss.

Calculate the average loss of the Coupler Cables in this Kit. Add the cable loss of

the cable provided with the GPSG-1000 to the average of the two cables provided

in this Kit and enter this value as cable loss.

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды