manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации


Поделиться
Скачать
background image

Specifications, Chapter 3 - Specifications

, 

139187 / Rev. 500

RGS-2000NG TCAS Test Set Operation Manual

1-3-1

September 2021

Subject to Export Control. See Cover Page for details.

Page 1

Chapter 3 - Specifications

RGS-2000NG Performance Specifications

NOTE:

A 60 MINUTE (1 HOUR) WARM-UP PERIOD IS REQUIRED FOR ALL 

SP E CI F I C A T I O NS .

SPECIFICATIONS  ARE  S U B J E CT   T O   CH A N G E  W I T HO UT   N O T I C E .

Please refer to these notes which are referenced throughout product specifications.

1

Absolute output power under any test condition is limited to the ranges shown for the transmitter power 
specifications. See 

“Power” on page 3

.

2

Pulse timing accuracy specifications applicable while transmitters configured for 50/50 ns 

rise/fall time mode only.

3

When transitioning between operating modes (high-to-low or low-to-high) a 30-minute waiting period is 
required for bearing accuracy to return to the stated specifications. 

4

Bearing accuracy specifications apply to the top antenna only when Avidyne OEM selected.

5

In XPDR test mode antenna measurements are taken from portsT2 and B2 when Collins Magnitude 
OEM is selected. For all other OEMs measurements are taken from antenna ports T1 and B1.

6

Pulse-timing, measurement-accuracy specifications applicable for input signals at amplitudes. +33 dBm.

7

With the exception of Mode S SLS, test-set transmit pulse-timing/amplitude specifications are not 
guaranteed under any test condition that results in overlapping pulse transmissions.

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 113956

ACS 3200 Series Operation And Instruction Manual preview
3200 Series
Бренд: ACS Страницы: 56
MacDon 912 Operator'S Manual preview
912
Бренд: MacDon Страницы: 84
MacDon 625 Operator'S Manual preview
625
Бренд: MacDon Страницы: 89
Patton electronics 2012 Installation And Operation Manual preview
2012
Бренд: Patton electronics Страницы: 18
TC Electronic M5000 Hardware Installation preview
M5000
Бренд: TC Electronic Страницы: 2
Bahco BBT80 Operating Instructions Manual preview
BBT80
Бренд: Bahco Страницы: 131
Bahco BBT60A Original Instructions Manual preview
BBT60A
Бренд: Bahco Страницы: 126
Eaton PowerXL DX-NET-ETHERNET2-2 User Manual preview
PowerXL DX-NET-ETHERNET2-2
Бренд: Eaton Страницы: 48
Eaton Power Xpert C445 Manual preview
Power Xpert C445
Бренд: Eaton Страницы: 2
Jandy AquaPure Ei Series Instructions preview
AquaPure Ei Series
Бренд: Jandy Страницы: 4
Jandy AquaPure Ei Series Manual preview
AquaPure Ei Series
Бренд: Jandy Страницы: 8
Jandy Jandy Pro Series Installation Manual preview
Jandy Pro Series
Бренд: Jandy Страницы: 16
YMC Pilot Manual preview
Pilot
Бренд: YMC Страницы: 49
Octane Fitness Q47 Product Safety Information preview
Q47
Бренд: Octane Fitness Страницы: 8
Octane Fitness LX8000 Preventative Maintenance And Diagnostics preview
LX8000
Бренд: Octane Fitness Страницы: 10
OCENCO M-20.2 Instruction Booklet preview
M-20.2
Бренд: OCENCO Страницы: 48
Ocean Optics NE-1 Installation And Operation Instructions Manual preview
NE-1
Бренд: Ocean Optics Страницы: 6
MacDon R1 FR Series Operator'S Manual preview
R1 FR Series
Бренд: MacDon Страницы: 238

Бренды по названию

Популярные бренды

Загрузить еще бренды