manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации

Поделиться
Скачать
Viavi 113956 Скачать руководство пользователя страница 286

Operation, 

Remote Operation

 

1-2-5

RGS-2000NG TCAS Test Set Operation Manual

139187 / Rev. 500

Page 14

Subject to Export Control. See Cover Page for details.

September 2021

5.5

MEASUREMENT COMMANDS

This set of commands allows the user to query the Unit to perform measurement on received signal from 
the UUT. The Unit can perform frequency, power and pulse characteristic measurements on both 1030 
and 1090 MHz signals. T he Unit can also perform 1030 MHz phase measurements between any of the 
antenna ports and either T1 or B1 according if top or bottom is selected.

5.5.1

DATA FORMAT

5.5.2

FREQUENCY REQUEST

5.5.3

MODE

Command Syntax:

{:RGS | :RGS2000NG}{:MEA | :MEASURE}{:DFORMAT}SP<numeric>CR

Description:

This command sets the replies numeric format.

Numeric:

0 to 2 (decimal ASCII)

Value

Format

0

Hexadecimal

1

Decimal (no fractional part)

2

Float (fractional part)

Default:

1

Example:

:RGS:MEA:DFORMAT 1\r

Command Syntax:

{:RGS | :RGS2000NG}{:MEA | :MEASURE}{:FREQ? | :FREQUENCY?} CR

Description:

This command returns the frequency of the incoming signal.

Return:

Value is in ASCII data format specified in MHz.
In case of the Float data format, the value is returned with four decimal 

points.

NOTE:

In order to measure frequency, the TCAS Unit needs to transmit a long P6 

pulse without modulation.

Example:

:RGS:MEA:FREQ?\r

Returns:

10A1C3 (Hexadecimal format) 

Returns:

1089976 (Decimal format) 

Returns:

1090.003 (Float format) 

Command Syntax:

{:RGS | :RGS2000NG}{:MEA | :MEASURE}{:SET | :SETTINGS}{:MOD | 

:MODE}SP<numeric>CR

Description:

This command sets the measurement mode.

Numeric:

0 to 2 (decimal ASCII)

Value

Measurement Mode

0

Pulse

1

Frequency 1030

2

Phase 1030

Default:

Pulse

Example:

:RGS:MEA:SET:MOD 0\r

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды