manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации


Поделиться
Скачать
background image

Operation, 

Screen Layout and Navigation

139187 / Rev. 500

RGS-2000NG TCAS Test Set Operation Manual

1-2-3

September 2021

Subject to Export Control. See Cover Page for details.

Page 203

3.7.1

NETWORK CONNECTIONS SCREEN

The Network Connections Screen is used to manage the Test Set’s network connections. The Network 
Connections Table displays information about the Test Set’s internal connections and external network 
connections. Refer to Section 

3.7.3, How to Configure Network Connections

 for instructions for changing 

the Test Set’s connections.

SCREEN SEQUE NCE:

Home Screen > System Softkey > Network Connections Softkey

Default Port Setting

All Ethernet communications to the RGS-2000NG are on Port 2001.

F i g u r e   1. 2 . 3   -   1 7 6   N e t w o r k   C o n n e c t i o n s  S c r e e n

Screen  Components

Descriptio n

Name

Displays the Name of the Ethernet Adapter. Names may vary.

Rear LAN

Indicates the Test Set’s Rear Panel LAN Connector.

Front LAN

Indicates the Test Set’s Front Panel LAN Connector.

DSP Connection

This is the Test Set’s internal connection. The Test Set’s internal 

connection is IP Address 192.168.0.1 (Factory Default Setting). 

The IP Address should not be changed.

IP Address

Displays the IP Address of the Ethernet Adapter.

IP Auto

Displays the IP Auto (DHCP Mode) of the Ethernet Adapter. 

Refer to Section 

3.7.3, How to Configure Network Connections

 

for instructions for changing an connections network mode.

Subnet Mask

Displays the Subnet Mask of the Ethernet Adapter.

Gateway

Displays the Gateway of the Ethernet Adapter.

Refresh Softkey

Updates the Network Connections Screen to display the current 

network settings of all the Ethernet adapters.

Change Settings Softkey

Displays the Network Connection Change Settings Screen.

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 113956

ABB ACS880-01 Series Installation Manual preview
ACS880-01 Series
Бренд: ABB Страницы: 238
DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Бренд: DARKSTAR TECHNOLOGIES Страницы: 4
TDW D2000 Maintenance Manuallines preview
D2000
Бренд: TDW Страницы: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Бренд: Taurus Страницы: 25
Vancare G Series Quick Reference Manual preview
G Series
Бренд: Vancare Страницы: 3
Paitec ES-2000 User Manual preview
ES-2000
Бренд: Paitec Страницы: 14
GE Ettan IPGphor 3 Instrument User Manual preview
Ettan IPGphor 3
Бренд: GE Страницы: 64
GE AMX 4+ Technical Publications preview
AMX 4+
Бренд: GE Страницы: 56
GE AMX 4+ Technical Manual preview
AMX 4+
Бренд: GE Страницы: 132
GE AKTAprocess Site Preparation Manual preview
AKTAprocess
Бренд: GE Страницы: 16
GE Logiq 500 Advanced Reference Manual preview
Logiq 500
Бренд: GE Страницы: 474
Keithley 263 Quick Reference Manual preview
263
Бренд: Keithley Страницы: 42
ACDC Mondo Installation Instructions preview
Mondo
Бренд: ACDC Страницы: 4
Ace AFM-5 Operating Manual preview
AFM-5
Бренд: Ace Страницы: 17
ACE INSTRUMENTS Solid Operating Manual preview
Solid
Бренд: ACE INSTRUMENTS Страницы: 33
ACE INSTRUMENTS ALP-1 med Quick Start Manual preview
ALP-1 med
Бренд: ACE INSTRUMENTS Страницы: 2
ACE INSTRUMENTS ACE Easy Quick Start Manual preview
ACE Easy
Бренд: ACE INSTRUMENTS Страницы: 2
TapFlo DT Series Original Instruction preview
DT Series
Бренд: TapFlo Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды