manualshive.com logo in svg

VIASYS Vmax Encore, Техническое справочное руководство

Поделиться
Скачать
VIASYS Vmax Encore Скачать руководство пользователя страница 2

ii

L2707

Vmax Encore

Technical Reference Manual

COPYRIGHT AND TRADEMARK NOTICES

© 2005 SensorMedics Corporation
All rights reserved. No part of this document may be reproduced, stored, or transmitted in 
any form or by any means without the written permission of SensorMedics Corporation, 
except as specifically permitted under the copyright laws of the United States of America.
VIASYS and the VIASYS logo are registered trademarks of VIASYS Healthcare Inc. Vmax, 
Autobox, MicroGard, and FreeFlow are trademarks of VIASYS Healthcare Inc. Perma Pure 
is a registered trademark of Perma Pure, Inc. Nafion is a registered trademark of E.I. du 
Pont de Nemours and Company. Microsoft and Windows are registered trademarks or 
trademarks of Microsoft Corporation. Other brands and their products are trademarks of 
their respective holders and should be noted as such.

COMPANY INFORMATION

www.viasyshealthcare.com

USA

SensorMedics Corporation                            
1100 Bird Center Drive
Palm Springs, CA 92262

Telephone:      800 231-2466

+1 714 283-2228

Fax: +1 714 283-8493

Authorized European Representative

VIASYS Healthcare GmbH
Leibnizstrasse 7
97204 Hoechberg
Germany

Telephone: +49 931 4972-0

Fax: +49 931 4972-423

Содержание Vmax Encore























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды