manualshive.com logo in svg

VIA Technologies EPIA-M920, Руководство пользователя, Страница: 74 / 93

Поделиться
Скачать
VIA Technologies EPIA-M920 Скачать руководство пользователя страница 74

VIA EPIA-M920 User Manual 

63

 

6.7.6.

 

SDIO_CR Configuration 

The SDIO_CR Configuration screen can be used to set SDIO_CR configuration parameters. 

 

 

Figure 69:  Illustration of SDIO_CR Configuration screen 

 

6.7.6.1.1.

 

SDIO Host Controller 

This feature has two options: Enable or Disable SDIO Host controller. 

6.7.6.1.2.

 

SDIO Specification Ver3.0 Support 

This feature has two options: Enable or Disable SDIO Specification Ver3.0 Support. 

6.7.6.1.3.

 

Voltage Support 1.8v 

This feature has two options: Enable or Disable Voltage Support 1.8v. 

6.7.6.1.4.

 

High Speed Support 

This feature has two options: Enable or Disable High Speed Support. 

6.7.6.1.5.

 

Driver Type Select  

Select Driver Type from Type A Type B, Type C and Type D. 

6.7.6.1.6.

 

SDR50 Support 

This feature has two options: Enable or Disable SDR50 Support. 

6.7.6.1.7.

 

SDR104 Support 

This feature has two options: Enable or Disable SDR104 Support. 

6.7.6.1.8.

 

DDR50 Support 

This feature has two options: Enable or Disable DDR50 Support. 

6.7.6.1.9.

 

SDR50 Tuning Enable 

This feature has two options: Enable or Disable SDR50 Tuning Enable. 

6.7.6.1.10.

 

Timer Count for Re-Tuning 

SDIO Timer Count for Re-Tuning. Available options are Re-Tuning Timer Disabled/1 sec/2 sec/4 sec/8 
sec/16 sec/32 sec/64 sec/128 sec/256 sec/512 sec/1024 sec/Get information from other source.  

Содержание EPIA-M920






























































































Отзывы:

Нет отзывов