VIA Technologies EPIA-M920 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 93

VIA Technologies EPIA-M920 Скачать руководство пользователя страница 65

VIA EPIA-M920 User Manual

54

6.6.8.

OnBoard Configuration

The OnBoard Device Configuration screen has the following features.

Figure 61: Illustration of OnBoard Configuration screen

OnBoard Device Configuration:

6.6.8.1.

OnBoard LAN Enable

The OnBoard LAN Enable feature determines whether the onboard LAN controller will be used or not.

6.6.8.2.

S5 Wakeup by PME#

The S5 Wakeup by PME# feature enables the BIOS to allow remote wake-up from the S5 power off state
through the PCI bus.

6.6.8.3.

EuP/ErP Lot6 support

The EuP/ErP Lot6 Support feature enables the BIOS to reduce the power draw to less than 1W when the
system is in standby mode. This feature has two options: enabled and disabled.

6.6.8.4.

1CH LVDS Backlight Control

Backlight Control
The Backlight Control feature control by VX11H enables the user to control the brightness of the 1CH
LVDS backlight. This feature has six options.

Level
0%, 20%, 40%, 60%, 80% and 100%.

6.6.8.5.

2CH LVDS Backlight Control

Backlight Control
The Backlight Control feature control by VX11H enables the user to control the brightness of the 2CH
LVDS backlight. This feature has six options.

Level
0%, 20%, 40%, 60%, 80% and 100%.

«
...
63
64
65
66
67
...
»

Содержание EPIA-M920






























































































Отзывы:

Нет отзывов