Vestil SWA-54, Инструкция по эксплуатации

Страница: 5 / 17

Table of Contents Rev. 4/23/2019 SWA-54 MANUAL
Table of Contents Copyright 2018 Vestil Manufacturing Corp. Page 5 of 17
Installation procedure (continued from p. 4)
4. Fasten the frame to the floor through all four anchoring tabs (2 are circled in the diagram on p. 4; there are 2 on
the opposite side as well). Each tab has a 9/16” hole located at its center. Drill holes for
1
/
2
” anchor bolts and
install them through the tab holes. Anchor bolt length should be determined by your facility engineer. Tighten the
anchors only to the point that the frame is level.
5. Shim and/or grout under the frame sides as necessary to prevent the frame from twisting.
6. Tighten all of the floor anchors wrench-tight.
7. Connect the wrapping machine to an AC power source: Plug the turntable power cord into a 115 VAC outlet.

[Only if unit equipped with powered mast] Powered mast models have 2 power cords: one for the turntable
and another for the wrapping carriage. The 2 cords can either both be plugged into a power outlet, or be
connected and plugged into an outlet. To connect the cords, plug the turntable power cord into the pigtail cord
of the mast control enclosure; then plug the power cord for the mast into a 115 VAC receptacle.
8. Test the powered functions:

Turntable rotation: press the foot pedal. The turntable
will rotate as long as the pedal is pressed.

Delta speed controller
: turn the speed control knob (in
diagram; also refer to the Delta operation manual).
Confirm that that the turntable rotates faster as the
speed control knob is turned clockwise, and slows
down when the knob is turned counterclockwise.

Powered mast models (option –PWO): raise and lower
the stretch wrap carriage with the UP and DOWN
buttons on the handheld control. Press and hold the
UP button. The carriage should automatically stop
moving when it reaches its upper travel limit. Press
and hold the DOWN button. Confirm that the carriage
stops on its own at the lower limit of travel. The
carriage should move smoothly up and down the mast.
10. Confirm that all labels are intact and easily readable. See
Labeling diagram on p. 15.
Carriage / Stretch Wrap Holder Assembly (SWH):
The wrap holder accommodates 10-20 inch rolls of stretch wrap.
Loading stretch wrap:
1. Unwind the wing nut (A) sufficiently to remove the lock spacer (6)
underneath the bottom retainer (2).
2. Remove the lock spacer.
3. Remove the bottom tube retainer (2).
4. Remove the spent roll of stretch wrap and install a new roll.
5. Reinstall the bottom tube retainer (2) and the lock spacer (6).
6. Tighten the wing nut (A) until the roll is snugly pressed between the
tube retainers (2) and (3). Adjust the tightness of the wing nut to
achieve the desired degree of material stretch—the tighter the wing
nut the more the wrap will stretch as it unrolls.
Item Part no. Description Quantity
1 20-014-116 Frame, rod, wrap retainer 1
2 20-014-006 Tube retainer (bottom) 1
3 20-014-005 Tube retainer (top) 1
4 20-110-002 Bearing, ball,
3
/
4
in., shield 1
5 68061 1
5
/
8
in. retainer ring 1
6 20-113-022 Spacer, lock 1
7 20-113-003
7
/
8
in. fiber washer 2
*8 SRF-18 20in. plastic wrap 1
*
Not included. The carriage accepts10”-20” rolls.
8
A
7
3
1
2
Speed
control
knob
Hand
brake
:
squeeze
to
release
carriage
NOTE:
Items 4 & 5 are
housed inside a cavity in the
bottom tube retainer.