Rev. 11/18/2019
LAD-EZ (6-12 STEPS), MANUAL
Copyright 2019 Vestil Manufacturing Co.
Page 18 of 20
) must solidly contact the ground before climbing the ladder. The caps resist sliding movement. They are included
to prevent the front end of the ladder from moving while they are in contact with the ground.
Face the ladder and grasp the handrails while ascending or descending the steps. Do not lean against the
handrails, the guardrails (around the platform), or the platform bar or chain. Do not lean over the handrails or
guardrails.
Moving the ladder:
After using the ladder, the mechanism that brings the front casters into ground contact must be reset. Lift the front
of the ladder while pressing down on one of the caster brackets. Caster brackets are identified on
Grasp the handrails and carefully push the ladder. Only try to move the ladder if you are able to comfortably lift the
front end and can easily control the ladder.
Storing the ladder
This ladder is designed for use both indoors and outdoors. However, it should only be stored indoors. The ladder
should be considered in storage whenever is has been unused for 30 minutes or more.
INSPECTIONS & MAINTENANCE
Inspect the unit as instructed. Inspections and all necessary repairs should be performed by qualified persons.
Compare the results of each inspection to the
. Do not use the ladder unless every
part is in satisfactory condition. If you have any questions about the condition of your ladder, contact the
department. The phone number is provided on the cover page of this manual.
Never make temporary repairs
of damaged or missing parts
. Only use manufacturer-approved replacement parts to restore the ladder to satisfactory
condition.
Before each use
inspect the ladder for any sustained damage, such as unusual wear, deterioration, or corrosion.
Look for loose connections. Tighten all loose connections. Whenever a lock nut is partially or completely unfastened,
it must be replaced with a new lock nut. Check cotter pins at each end of the wheel axle, the wheels, and the square
caps (99-024-027) for damage.
Regular inspections
—
at least once per month
inspect the following items. Replace all parts not in satisfactory
condition before returning the ladder to service. DO NOT continue to use the ladder if damage cannot be repaired.
•
Handrails, guardrails, back frame weldment (platform bar), snap hooks, and platform chains: Confirm that both
handrails are solidly fastened to the step weldment and to the platform. Each handrail should be straight, rigid, and
undamaged. Examine the guardrails around the platform for damage, bends, and cracks. Examine the platform bar
and, if applicable, the chain and snap hooks. Confirm that the bar and chain are undamaged and securely fastened
to the guard railing. Snap hooks should close automatically.
•
Rear wheels (16-132-310): Check the wheels. They must not be significantly worn, i.e. must still have ~1/8” of
tread. Wheels must not be cracked, warped, broken, etc. They should be vertical (not bent towards, or away from,
the ladder) and roll smoothly. Examine the wheel axle and cotter pins (65127) for damage.
•
Frame members (step weldment, back leg weldment, base supports), handrails, and all fasteners (bolts, nuts,
pins): Inspect each frame member for damage. In particular, look for excessive wear, bends, cracks, warps,
damaged welds, and looseness. All frame pieces should be square, rigid, and free of rust and corrosion. Remove
rust and apply touch-up paint to the affected area. Check the areas where components are fastened/bolted
together. Check for cracks around bolt holes, elongated bolt holes, etc.
•
Square caps (99-024-027): Check the caps for cracks, tears, and wear. If either cap is not in satisfactory condition,
install a replacement cap before returning the ladder to service. Even a moderate amount of wear can affect the
performance of a cap.
•
[LAD-11 and LAD-12] Outriggers and outrigger fasteners (bolts, nuts): Examine the outriggers (44-514-310 & 44-
514-311). Both should be undamaged and be securely fastened to the step weldment. Both outriggers should
make solid contact with the ground. The ladder should not wobble. Confirm that the caps on the outrigger legs are
in satisfactory condition.
Maintenance
: Regular maintenance is required for the ladder to function properly for as long as possible. in
addition to correcting issues discovered during inspections, maintain the ladder in the following ways.
•
Clean the ladder with a damp cloth to remove dirt and grime, especially from step surfaces. Let the ladder dry
completely before returning it to service.
•
[6-12 step models] Lubricate bolts as necessary for the wheels to rotate freely.
•
Apply touchup paint wherever the finish is damaged. Apply touchup paint as soon as damage occurs.
