Vesper AIS WatchMate 850 Скачать руководство пользователя страница 6

Страница: 6 / 62

- 6 -

Compass Safe Distance

Mount your

AIS

WatchMate

transponder at least 0.6m (2 feet) from any compass. Test your

compass to verify that it operates properly when this device is operating.

Electronic Waste Recycling

Various regional and national regulations exist regarding the recycling of certain
electronics. Please consult your local authorities or contact Vesper Marine for
recycling information.

Care Notice

To provide protection against the damaging effects of UV light, it is recommended to replace
the cover when not in use.

Take care when cleaning to avoid damage:



Be careful when wiping the display screen to avoid scratching. Use a clean soft damp
cloth.



Do not use acid, ammonia, solvents, or any abrasive products.

Declaration of Conformity

Vesper Marine declares that this AIS Aid to Navigation is in compliance with Directive
2014/53/EU.

The full text of the EU Declaration of Conformity is available at the following internet
address:

www.vespermarine.com/compliance

This product is for use worldwide, including the following countries:

This device is also approved for use in the United States, Canada, Australia and New
Zealand.

0168

Содержание AIS WatchMate 850































































Результаты поиска

Содержание AIS WatchMate 850

Отзывы:

Vesper AIS WatchMate 850, Руководство пользователя, Страница: 6 / 62

Результаты поиска

Содержание AIS WatchMate 850

Отзывы: