VESPA GTS Super 125 i.e. страница 54 Скачать руководство пользователя

Страница: 54 / 285

This section makes it possible to find what solutions to apply when troubleshooting.

For each failure, a list of the possible causes and pertaining operations is given.

Engine

Excessive oil consumption/Exhaust smoke

EXCESSIVE CONSUMPTION

Possible Cause

Operation

Wrong valve adjustment

Adjust the valve clearance properly

Overheated valves

Remove the head and the valves, grind or replace the valves

Misshapen/worn valve seats

Replace the head unit

Worn cylinder, Worn or broken piston rings

Replace the piston cylinder assembly or piston rings

Worn or broken piston rings or piston rings that have not been

fitted properly

Replace the piston cylinder unit or just the piston rings

Oil leaks from the couplings or from the gaskets

Check and replace the gaskets or restore the coupling seal

Worn valve oil guard

Replace the valve oil seal

Worn valve guides

Check and replace the head unit if required

Insufficient lubrication pressure

POOR LUBRICATION PRESSURE

Possible Cause

Operation

By-Pass remains open

Check the By-Pass and replace if required. Carefully clean the

By-Pass area.

Oil pump with excessive clearance

Perform the dimensional checks on the oil pump components

Oil filter too dirty

Replace the cartridge filter

Oil level too low

Restore the level adding the recommended oil type

Transmission and brakes

Clutch grabbing or performing inadequately

IRREGULAR CLUTCH PERFORMANCE OR SLIPPAGE

Possible Cause

Operation

Faulty clutch

Check that there is no grease on the masses. Check that the

clutch mass faying surface with the bell is mainly in the centre
with equivalent characteristics on the three masses. Check that
the clutch housing is not scored or worn in an anomalous way

Insufficient braking

INEFFICIENT BRAKING SYSTEM

Possible Cause

Operation

Inefficient braking system

Check the pad wear (1.5 min). Check that the brake discs are
not worn, scored or warped. Check the correct level of fluid in

the pumps and change brake fluid if necessary. Check there is
no air in the circuits; if necessary, bleed the air. Check that the

front brake calliper moves in axis with the disc.

Fluid leakage in hydraulic braking system

Failing elastic fittings, plunger or brake pump seals, replace

Troubleshooting

Vespa GTS Super 125 i.e.

TROUBL - 54

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды