VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 124

VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 14

VESDA-E VES-A00-P Product Guide

8

www.xtralis.com

Use USB

Use WiFi

or Ethernet

Initial

Configuration

Monitoring and

Configuration Updates

Connection

Usage?

Figure 2-3: Connection Method

The physical communication ports are located on the main board inside the detector. It is necessary to open
the front door in order to access these ports. Refer to Section 7.2 for information on opening the front door.

USB

The USB port is used for configuration purposes ONLY. It allows direct connection between the VES-A00-P
detector and a PC or laptop running the Xtralis VSC software.

Note:

The USB port must not be used for permanent field connection.

Ethernet

The Ethernet port is used for configuration and/or monitoring purposes. It enables direct or routed network
connection between the detector and a PC or laptop installed with Xtralis VSC.

WIFI

The WiFi module provides wireless connection of the detector to the building network for the purpose of
configuration and secondary monitoring with Xtralis VSC.

2.6

VESDAnet

A VESDAnet network allows:

l

the VES-A00-P detector to report alarms and faults to a Fire Panel using a remote display module,
remote relay module or HLI.

l

configuration and monitoring of devices from a central computer.

l

connection to a reference detector.

Gateway function of the VES-A00-P

The VES-A00-P detector also provides a gateway to the VESDAnet for a PC running Xtralis VSC connected
to the VES-A00-P via Ethernet, USB or WiFi.

«
...
12
13
14
15
16
...
»

Содержание VESDA-E VES-A00-P





























































































































Отзывы:

Нет отзывов