Vertex Standard VX-2500U, Руководство по обслуживанию

Страница: 11 / 79

11
Circuit Description
1. Overview
The VX-2500U is a UHF FM mobile transceiver designed
to operate in the frequency range of 400 to 520 MHz.
2. Circuit Configuration by Frequency
The receiver is a double-conversion superheterodyne with
a first intermediate frequency (IF) of 44.25 MHz and a
second IF of 450 kHz. Incoming signals from the antenna
are mixed with the local signal from PLL to produce the
first IF of 44.25 MHz.
This is then mixed with the 43.8 MHz second local oscil-
lator (using the 14.6 MHz reference crystal) output to pro-
duce the 450 kHz second IF. This is detected to give the
demodulated signal.
The transmit signal frequency is generated by PLL VCO,
and modulated by the signal from the microphone. It is
then amplified and sent to the antenna.
3. Receive Signal Path
Incoming RF signals from the antenna connector are de-
livered to the RF Unit, and pass through a low-pass filter
(LPF) antenna switching network consisting of coils L1001,
L1002, L1003, L1005, and L1007, capacitors C1004,
C1009,C1016, C1019, and C1025, and antenna switching
diodes
D1005 and D1007 (both XB15A709A0HR ) for de-
livery to the receiver front end.
Signals within the frequency range of the transceiver are
then passed through a varactor-tuned bandpass filter con-
sisting of L1008, L1009 before RF amplification by
Q1011
( 2SC4227 :Ver. D or 2SC4226 :Ver. CS1, DS1).
The amplified RF is then band-pass filtered again by var-
actor-tuned resonators L1019, L1023 to ensure pure in-
band input to 1st mixer
Q1026 ( 3SK228 :Ver. D or
SGM2016AM :Ver. CS1, DS1).
Buffered output from the VCO Unit is amplified by Q1021
( 2SC5107 ) and low-pass filtered by L1030/L1032 and
C1184/C1188/C1192, to provide a pure 1st local signal
between 355.75 and 475.75 MHz to the 1st mixer.
The 44.25 MHz 1st mixer product then passes through
dual monolithic crystal filters XF1001 and XF1002, and is
amplified by
Q1029 ( 2SC4215Y ) and delivered to the in-
put of the FM IF subsystem IC Q1028 ( TA31136FN ).
This IC contains the 2nd mixer, 2nd local oscillator, limit-
er amplifier, FM detector, noise amplifier, and squelch
gates.
The 2nd LO in the IF-IC is produced from crystal X1001
(14.600 MHz), and the 1st IF is converted to 450 kHz by
the 2nd mixer and stripped of unwanted components by
ceramic filter CF1001 or CF1002. After passing through a
limiter amplifier, the signal is demodulated by the FM
detector
CD1001 ( CDBC450CX24 ).
Detected audio from Q1029 is applied to Q2016 ( AK2345 )
and audio low-pass filter. After volume adjustment by
Q2014 ( M62364FP ), the audio signal is amplified by the
AF power amplifier Q1509 ( TDA2003H ) and passed to
speaker jack.
4. Transmit Signal Path
Voice audio from the microphone is delivered via the MIC
(Jack) Unit to the PANEL Unit, after passing through
amplifier
Q2022 ( NJM2902V ), Mic gain-volume Q2014
( M62364FP ) pre-emphasis Q2015 ( NJM2902V ), and lim-
iter Q2016 (IDC instantaneous deviation control), is ad-
justed for optimum deviation level and delivered to the
next stage.
Voice input from the microphone and CTCSS are FM-
modulated to the VCO of the synthesizer, while DCS au-
dio is modulated by the reference frequency oscillator of
the synthesizer.
Synthesizer output, after passing through diode switch
D1022 ( 1SS321 ), is amplified by driver Q1022
( 2SC5415E ), Q1025 ( 2SC5107 :Ver. D or 2SC4226 :Ver.
CS1, DS1) and power module Q1014 ( RA30H4452M :Ver.
D, DS1 or RA30H4047M :Ver. CS1) to obtain full RF out-
put. The RF energy then passes through antenna switch
D1005 / D1007 and a low-pass filter circuit and finally to
the antenna connector.
RF output power from the final amplifier is sampled by
CM coupler and is rectified by
D1011 , D1012 (both
HSM88AS ). The resulting DC is fed through Automatic
Power Controller Q1003 ( M 5 2 2 3 A G P ) , Q1002
( 2SC4154E ), Q1032 ( 2SC4254E ), and TH1003 to trans-
mitter RF amplifier and thus the power output.
Generation of spurious products by the transmitter is min-
imized by the fundamental carrier frequency being equal
to the final transmitting frequency, modulated directly in
the transmit VCO. Additional harmonic suppression is
provided by a low-pass filter consisting of L1002, L1003,
L1005, C1004, C1009, C1016, C1019, and C1025, resulting
in more than 60dB of harmonic suppression prior to de-
livery to the RF energy to the antenna.
5. PLL Frequency Synthesizer
PLL frequency synthesizer consists of the VCO Q1013
( 2SK508-K52 : RX) and Q1015 ( 2SC4226-R24 : TX), VCO
buffers Q1018 , Q1020 , Q1021 (all 2SC5107-0 ), PLL sub-
system IC Q1023 ( SA7025DK :Ver. D) or Q1038
( MB15A02PFV1 :Ver. CS1, DS1) and 14.6 MHz reference
crystal X1001.
The frequency stability is ±2.5ppm within temperature
range of –30 to +60 degree. The output of the 14.6 MHz
reference is applied to pin 8 (Ver. D) or pin 1 (Ver. CS1,
DS1) of the PLL IC.