Versitron Web Smart+ SG71070M Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 123

Versitron Web Smart+ SG71070M Скачать руководство пользователя страница 58

52

SG71070M

Revision A3

Select the IPMC Profile as the filtering condition for the specific port. Summary about the
designated profile will be shown by clicking the view button.

2-10 VLANS

Assign a specific VLAN for management. The management VLAN is used to establish an IP
connection to the switch from a workstation connected to a port in the VLAN. This connection
supports a VSM, SNMP, and Telnet session. By default, the active management VLAN is VLAN 1,
but you can designate any VLAN as the management VLAN using the Management VLAN
window. Only one management VLAN can be active at a time.

When you specify a new management VLAN, your HTTP connection to the old management
VLAN is lost. For this reason, you should have a connection between your management station
and a port in the new management VLAN or connect to the new management VLAN through a
multi-VLAN route.

Web Interface

To configure VLAN Configuration in the web interface:

1.

Click Configuration VLANS.

2.

Specify Existing VLANS, Ether type for Custom S-ports.

3.

Click Apply.

Figure 2-10: The VLAN Configuration

Parameter description:



Allowed Access VLANS

This field shows the allowed Access VLANS, it only affects ports configured as Access ports.
Ports in other modes are members of all VLANS specified in the Allowed VLANS field.

By default, only VLAN 1 is enabled. More VLANS may be created by using a list syntax where

«
...
56
57
58
59
60
...
»

Содержание Web Smart+ SG71070M




























































































































Отзывы:

Нет отзывов