VersaLogic Viper VL-EBX-38EBP Скачать руководство пользователя страница 51

Страница: 51 / 79

Video Interfaces

EBX-38 Hardware Reference Manual

Mini DisplayPort Connectors

The Mini DisplayPort connectors J3 and J30 both support resolutions up to 2560 x 1440 at 24-

bit.
DisplayPort consists of three interfaces:



Main Link – transfers high-speed isochronous video and audio data



Auxiliary channel – used for link management and device control; the EDID is read over

this interface



Hot Plug Detect – indicates that a cable is plugged in

Connector J3 DisplayPort interface also supports:



Audio signaling (Audio is disabled by default in BIOS Setup so it would need to be

enabled before use.)



DP++ mode allowing connection to an HDMI device through a passive adapter.

“Passive” means that the adapter does not require external power (because it uses the DP

port’s 3.3 V power) and it does not require software drivers.

The figure below shows the locations of the 20-pin Mini DisplayPort connectors. Table 20 lists

the pinout of the J3 Mini DisplayPort0 connector and J30 Mini DisplayPort1 connector.

Figure 20. Location of the Mini DisplayPort Connectors

Содержание Viper VL-EBX-38EBP
















































































Результаты поиска

Содержание Viper VL-EBX-38EBP

Отзывы:

Бренды по названию

Популярные бренды

VersaLogic Viper VL-EBX-38EBP, Справочник по аппаратуре

Результаты поиска

Содержание Viper VL-EBX-38EBP

Отзывы:

Бренды по названию

Популярные бренды