manualshive.com logo in svg

VersaLogic Owl, Справочник по аппаратуре

Поделиться
Скачать
VersaLogic Owl Скачать руководство пользователя страница 21

Board Features 

21 

VL-EPU-4012 Hardware Reference Manual 

 

Table 3: Main Power Connector Pinout 

Pin 

Signal 

Description 

 

Pin 

Signal 

Description 

1 

V_MAIN 

Main input voltage 

(+8V to +30V) 

 

2 

V_MAIN 

Main input voltage 

(+8V to +30V) 

3 

EARTH_GND 

Earth ground 

 

4 

V_MAIN 

Main input voltage 

(+8V to +30V) 

5 

POWER_FAULT 

An open-drain signal 

•

 

Low if power is OK 

•

 

Open if there is a 
power fault 

(Note)

 

 

6 

GND 

Signal ground 

7 

GND 

Signal ground 

 

8 

GND 

Signal ground 

Note:

  A power fault can be due any of the following conditions: 

•

 

The input power is off. 

•

 

The main input regulator has failed. 

•

 

The power input is under- or over-voltage (not in the 8 - 30V range). 

Cabling 

An adapter cable, part number VL-CBR-0809, is available for connecting the Owl to an ATX 
power supply.  

If your application requires a custom cable, the following information will be useful: 

VL-EPU-4012 Board Connector 

Mating Connector 

Molex 055959-0830 

Molex 051353-0800 

Power Requirements 

The Owl requires a 8 to +30 VDC supply capable of providing at least 35 W average 
power that can also provide a peak power of 50 W. The input DC supply creates both the standby 
and payload voltages provided to the CPU module. 

The exact power requirements for the Owl depend on several factors, including CPU 
configuration (the number of cores, CPU clock rate), memory configuration, peripheral 
connections, and attached devices, and others. For example, driving long RS-232 lines at high 
speed can increase power demand. 

The VersaLogic VL-PS-ATX12-300A is a 1U size ATX power supply suitable for use with the 
Owl. Use the VL-CBR-0809 adapter cable to attach the power supply to the main power 
connector. 

Power Delivery Considerations 

Using the VersaLogic approved power supply (VL-PS-ATX12-300A) and power cable 
(VL-CBR-0809) will ensure high quality power delivery to the board. Customers who design 
their own power delivery methods should take into consideration the guidelines below to ensure 
good power connections. 

 

Содержание Owl








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды