VersaLogic Fox VL-EPM-19 страница 34 Скачать руководство пользователя | Manualshive

Страница: 34 / 61

background image

EPM-19 Hardware Reference Manual

25

Multi-purpose I/O

USB

The USB interface on the EPM-19 is OHCI (Open Host Controller Interface) and EHCI
(Enhanced Host Controller Interface) compatible, which provides a common industry
software/hardware interface. The USB controller can be enabled or disabled in the BIOS Setup
utility. The board has four USB ports:



Two hub ports routed to the J9 user I/O connector. Table 11 page 30 lists the USB port
signals routed to the J9 user I/O connector.



Two additional non-hub ports are also routed to the J9 user I/O connector.



Note:

Some USB mass storage devices cause long delays or reboot cycles when formatted

as non-bootable FAT32 drives.

The USB interfaces at connector J9 are accessible using a CBR-4005B paddleboard or by using a
custom cable.

All four USB ports use IEC 61000-4-2-rated TVS components to protect against ESD damage.

PCIe Mini Card / mSATA

The socket at location J2 accepts a full-height PCI Express Mini Card or an mSATA module.



Note:

PCIe Mini Cards using small (512 byte or below) I/O address ranges may not be accessible.

The PCIe Mini Card interface includes one PCIe x1 lane, one hubbed USB 2.0 channel, and the
SMBus interface. The socket is compatible with plug-in Wi-Fi modems, GPS receivers, Flash
data storage, and other cards for added flexibility. For more information on PCIe Mini Cards
offered by VersaLogic, contact

[email protected]

To secure a Mini Card or mSATA module to the on-board standoffs, use two M2.5 x 6mm pan
head Philips nylon screws. These screws are available in quantities of 10 in the VL-HDW-108
hardware kit from VersaLogic.

Table 8: PCIe Mini Card / mSATA Pinout

J2

Pin

PCIe Mini Card

Signal Name

PCIe Mini Card

Function

mSATA

Signal Name

mSATA

Function

1

WAKE#

Wake

Reserved

Not connected

2

3.3VAUX

3.3V auxiliary source

+3.3V

3.3V source

3

NC

Not connected

Reserved

Not connected

4

GND

Ground

GND

Ground

5

NC

Not connected

Reserved

Not connected

6

1.5V

1.5V power

+1.5V

1.5V power

7

NC

Not connected

Reserved

Not connected

8

NC

Not connected

Reserved

Not connected

9

GND

Ground

GND

Ground

5

«
...
32
33
34
35
36
...
»

Содержание Fox VL-EPM-19






























































Отзывы:

Нет отзывов

Похожие инструкции для Fox VL-EPM-19

Бренд: Baicells Страницы: 8

Бренд: NXP Semiconductors Страницы: 24

Бренд: SeaLevel Страницы: 17

Бренд: SIIG Страницы: 12

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

Бренд: Arbor Technology Страницы: 8

PCM-4141 Series

Бренд: Advantech Страницы: 96

X-NUCLEO-EEPRMA1

Бренд: ST Страницы: 22

ARC-12x4 Series

Бренд: Areca Страницы: 2

Бренд: Digital Equipment Страницы: 90

AH10EN-5A Series

Бренд: Delta Страницы: 132

Hotwire 5620 RTU

Бренд: Paradyne Страницы: 20

Бренд: IBASE Technology Страницы: 49

NetStructure ZT 5085

Бренд: Intel Страницы: 106

ControlCenter-IP 2.0

Бренд: G&D Страницы: 60

4 Channel Fan Speed Control Module CLX-1FAN4

Бренд: Crestron Страницы: 1

Pentium Pro Family

Бренд: Intel Страницы: 328

Бренд: Faroudja Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды