VersaLogic Fox VL-EPM-19 страница 9 Скачать руководство пользователя

Страница: 9 / 61

Contents

EPM-19 Hardware Reference Manual

Table 5: Expansion Current Limits ................................................................................... 16

Table 6: Battery Saver Jumper Truth Table ...................................................................... 18

Table 7: No Battery Mode Jumper Truth Table ................................................................ 19

Table 8: PCIe Mini Card / mSATA Pinout ....................................................................... 25

Table 9: Primary Boot Device Truth Table ....................................................................... 27

Table 10: PCIe Mini Card LED States .............................................................................. 28

Table 11: J9 I/O Connector Pinout and Pin Orientation ................................................... 30

Table 12: J7 COM1/COM2 Connector Pinout ................................................................. 32

Table 13: J6 COM3/COM4 Connector Pinout ................................................................. 32

Table 14: Recommended Serial Port Settings for Vortex86DX2 BIOS ........................... 33

Table 15: COM3/COM4 Termination Jumpers ................................................................ 34

Table 16: J8 VGA Video Output Pinout ........................................................................... 37

Table 17: J15 LVDS Flat Panel Display Connector Pinout .............................................. 39

Table 18: Compatible LVDS Interface TFT-Technology Flat Panel Displays ................. 39

Table 19: BIOS Settings for Boot Display Devices and Corresponding Resolutions ...... 40

Table 20: Ethernet Connector Pinout ................................................................................ 43

Table 21: On-board Ethernet Status LEDs (D3 and D8) ................................................. 44

Table 22: SPX Connector Pinout ...................................................................................... 46

Table 23: PC/104 ISA I/O, IRQ, and Memory Resources ................................................ 47

Table 24: User I/O Connector Pinout ............................................................................... 50

Table 25: Auxiliary I/O Connector Pinout ........................................................................ 51

Содержание Fox VL-EPM-19






























































Результаты поиска

Содержание Fox VL-EPM-19

Отзывы:

Похожие инструкции для Fox VL-EPM-19

Бренды по названию

Популярные бренды

VersaLogic Fox VL-EPM-19, Справочник по аппаратуре

Результаты поиска

Содержание Fox VL-EPM-19

Отзывы:

Похожие инструкции для Fox VL-EPM-19

Бренды по названию

Популярные бренды