background image

17

Encore

®

 1450CE Non-Catalytic Woodburning Stove

30003845

ST264
good fire
12/99

ST64

fig. 25

  Add larger pieces of wood as the fire begins to burn 

well.

Once the draft is established, open the front door and 
light the rest of the fuel from the bottom.  Do not light 
the main bed of fuel until the chimney begins drawing, 
and repeat the procedure as often as necessary if the 
initial attempt is unsuccessful.
If your Encore has been broken-in previously using, 
continue to build the fire gradually. Add larger wood with 
a diameter of 76-10 mm (3-4”).  Continue adding split 
logs of this size to the briskly-burning fire until there is 
a glowing ember bed  at least 76 mm (3”) deep. A good 
ember bed is necessary for proper functioning of the 
combustion system and may take an hour or more to 
establish.  

refuel while the embers are Still hot

When reloading, best results will be achieved if you first 
de-ash the stove by stirring the fuel bed to allow ash to 
fall through the grate into the ash pan.
Do not break the charcoal into very small pieces or 
pound or compress the charcoal bed.
It is important that air can circulate through the charcoal 
bed while the heater is in operation. Larger pieces of 
charcoal allow more air to circulate under the wood,  
resulting in the fire reviving more quickly.
For best results when refueling, wear stove gloves to 
protect your hands, add fuel while the stove still has 

ST264a
add wood fire
11/00

ST64a

fig. 26 

 Add full-size logs when the kindling has burned down 

to a bed of embers.

plenty of glowing embers to re-kindle the fire, and 
include some smaller pieces of wood in the new fuel 
load to help the stove regain its operating temperature 
quickly.  Use this sequence as a guide to successful 
refueling. 

Note:

 Door handles can be hot. A glove has been 

included with your stove. We recommend using this 
glove whenever operating door or damper controls and 
especially when operating the top griddle.
1.  Open the damper.
.  De-ash the stove as described above. Open the 

front doors and check the level of ash in the ash 
pan. Empty the pan if necessary and replace it in the 
stove. Close the front doors.

3.  Open the griddle, load the wood (smaller pieces 

first), and close the griddle.

4.  Allow the stove to regain its “thermal momentum” 

before closing the damper. This may take 15--0 
minutes.

5.  Close the damper and set the air control lever for the 

desired heat output. When the surface temperature 
reaches 30° C (450° F), adjust the air control for 
the amount of heat you desire.

Note:  

If the charcoal bed is relatively thick {about 51-

76 mm (”-3”)} deep, and if your fuel is well seasoned, it 
is possible to add fresh fuel (smaller pieces first), close 
the door and damper, and reset the primary air control 
for the desired heat output within five minutes.

warNiNg:  fireplace StoveS equipped with 
doorS Should be operated oNly with 
doorS fully opeN or doorS fully cloSed. 
if doorS are left partly opeN, gaS aNd 
flame may be drawN out of the fireplace 
Stove opeNiNg creatiNg riSkS from both 
fire aNd Smoke.
cautioN:  the encore will be hot while in opera-
tion.  keep children, clothing and furniture away.  
contact may cause skin burns.

do Not overfire thiS heater.

  Overfiring may 

cause a house fire, or can result in permanent dam-
age to the stove and to the catalytic combustor.  If 
any part of the Encore glows, you are overfiring.

Содержание Encore 1450C





























Отзывы: