manualshive.com logo in svg

Vermeer S925TX, Руководство оператора, Страница: 53 / 104

Поделиться
Скачать
Vermeer S925TX Скачать руководство пользователя страница 53

S925TX Mini Skid Steer 

Shutdown Procedure    23-1

Section 23:  Shutdown Procedure

•

For your safety and the safety of others, use the shutdown procedure before working on the machine for any 
reason, including servicing, cleaning, or inspecting the machine.

Step 1:

Park machine on a level surface.

Step 2:

Move 

Ground Drive

 

Joystick

 to NEUTRAL.

Step 3:

Move 

Auxiliary Attachment Drive Lever 

to NEUTRAL.

Step 4:

Fully lower attachment onto the ground.

Step 5:

Move 

Throttle

 to low position and allow engine to idle for 1 to 5 minutes before shutting down.

Please consult machine’s engine manual for shutdown details.

Step 6:

Shut off engine and remove key.

A variation of the above procedure may be used if so instructed within this manual or if an emergency requires it.

Park brake will engage when operator steps off platform or engine is shut off and spring-applied park brake pin 
is aligned between sprocket teeth.

Содержание S925TX









































































































Отзывы:

Нет отзывов