Vermeer 504 PRO Скачать руководство пользователя страница 95

Страница: 95 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

•

Using pliers withdraw the knives rearward, then diagonally upwards from the knife axle and remove them from the knife slots.

Figure 52. Knive axle lever

NOTICE

Removed knives should be replaced by blank knives (part no. 1724551237W) to prevent plugging of the knife slots.

•

Both blank and removed knives can be stored and secured with a cotter pin on the maintenance platform (see Figure 53 on page 7-33).

If no cutting function is desired for a longer period of time, removed knives must be replaced by blank knives (see Figure 54 on page 7-33):

•

[1] Insert blank knives into the knife slots.

•

[2] Rotate blank knives downward into knife slots.

•

[3] Blank knives shown in final position.

•

Rotate knife axle lever up and rearward 90 degrees until it contacts upper stop.

•

Release tailgate safeguard and close tailgate.

•

Close Hydroflexcontrol-bottom door.

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды