Vermeer 504 PRO Скачать руководство пользователя страница 39

Страница: 39 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

D. OK (Enter)

Push OK to accept the active selection
(selected with the Up or Down button)

4. Hydroflex floor

Push Hydroflex floor to switch the function of
the double acting valve in the tractor to lift/
lower the Hydroflex floor.

9. Task

Push Task to activate the page for entering
tasks

E. Toggle

Push Toggle to switch between the virtual
terminal menus and the baler application

5. Pick-up

Push Pick-up to switch the function of the
double acting valve in the tractor to lift/lower
the pick-up.

10. Advanced

Push Advanced to activate the page where
advanced settings can be made

Figure 10. E-link Pro buttons

5.2

Setup the E-link Pro Display

Preparation

1. Make sure the E-link pro is connected to the baler.

2. Switch on the E-link with the On/Off button (A) (see page 5-2)

3. Push the toggle button

(F5), the configuration page appears.

Setup Country and Language

1. Push [

] (F8) (see page 5-2) on a configuration page.

The page "Regional Configuration" appears.

2. Push the line "Country".

3. Push the button [

] or [

] to select your country.

4. Push [OK] to confirm the country and return to the page "Regional Configuration".

5. Push the line "Language".

6. Push the button [

] or [

] to select your language.

7. Push [OK] to confirm the language and return to the page "Regional Configuration".

Refresh and reboot the controller. The language on the display is now in the selected language.

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды