VERDER VERDERAIR VA 25 Скачать руководство пользователя | Manualshive

Страница: 13 / 35

background image

859.0089

13

Diaphragms and Center Section

Disassembly

NOTE: Diaphragm kits are available in a range of materi-
als and styles. See page 27 to order the correct dia-
phragms for your pump. A Center Rebuild Kit also is
available. See page 23. Parts included in the Center
Rebuild Kit are marked with an *. For best results, use all
kit parts.

1.

Follow the Pressure Relief Procedure on page 9.

2.

Remove the manifolds and disassemble the ball
check valves as explained on page 12.

3.

Overmolded Diaphragms

a.

Orient the pump so one of the fluid covers faces
up. Use a 10 mm socket wrench to remove the
fluid cover screws (7), then pull the fluid cover (3)
up off the pump.

b.

The exposed diaphragm (15) will screw off by
hand from the diaphragm shaft (104). The dia-
phragm shaft bolt will remain attached to the dia-
phragm. Remove the air side diaphragm plate
(14).

c.

Turn the pump over and remove the other fluid
cover. Pull the diaphragm and shaft up through
the center housing.

d.

Grasp the diaphragm firmly and use a wrench on
the flats of the shaft to remove. Also remove the
air side diaphragm plate (14). Continue with Step
5.

4.

All Other Diaphragms

a.

Orient the pump so one of the fluid covers faces
up. Use a 10 mm socket wrench to remove the
fluid cover screws (7), then pull the fluid cover up
off the pump. Turn the pump over and remove
the other fluid cover.

b.

Plastic Pumps: Use a 1-1/4 socket or box end
wrench on the hex of a fluid side diaphragm plate
to remove. Then remove all parts of the dia-
phragm assembly. See F

IG

. 7.

Metal Pumps: Remove the bolt (304) from one
side of the diaphragm shaft, then remove all
parts of that diaphragm assembly. See F

IG

. 7.

c.

Follow the same procedure to disassemble the
other diaphragm assembly.

5.

Inspect the diaphragm shaft (104) for wear or
scratches. If it is damaged, inspect the bearings
(105) in place. If they are damaged, use a bearing
puller to remove them.

NOTE: Do not remove undamaged bearings.

6.

Use an o-ring pick to remove the u-cup packings
(106) from the center housing. Bearings (105) can
remain in place.

7.

Use a socket wrench to remove the pilot valves
(101).

8.

Remove the pilot valve cartridges only if necessary
due to a known or suspected problem. After remov-
ing pilot valves, use a hex to remove the cartridges
(102), then remove o-rings (103). If stripped, use two
screwdrivers to screw out the cartridge.

NOTE: Do not remove undamaged pilot valve
cartridges.

«
...
11
12
13
14
15
...
»

Содержание VERDERAIR VA 25




































Отзывы:

Нет отзывов

Похожие инструкции для VERDERAIR VA 25

Бренд: A.O. Smith Страницы: 65

Бренд: YAMADA Страницы: 18

Бренд: Kärcher Страницы: 18

Бренд: Wayne Страницы: 8

Бренд: Wacker Neuson Страницы: 46

EcoPart 400 230V 1N~

Бренд: CTC Union Страницы: 40

Бренд: Masterflex Страницы: 28

CENTRO-MATIC 85430

Бренд: Lincoln Страницы: 14

Бренд: Grundfos Страницы: 8

Бренд: Homa Страницы: 40

Бренд: DAE Pumps Страницы: 29

Бренд: Reefe Страницы: 14

Бренд: Pentair Страницы: 8

Myers ME40 Series

Бренд: Pentair Страницы: 12

Бренд: Dräger Страницы: 28

Бренд: BMC Страницы: 48

FUTERA II Series

Бренд: RBI Страницы: 48

Бренд: Hi-Force Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды