manualshive.com logo in svg

Verco Oblique Visual OVRT 0806, Инструкция по сборке, Страница: 1 / 4

Поделиться
Скачать
Verco Oblique Visual OVRT 0806 Скачать руководство пользователя страница 1

Oblique Visual desking

OVRT 0806/1006/1206/1208/1408/1608/1808/2008/2408

OVWT 1208/1408/1608/1809/2009/2409

4+ unit back to back Oblique Visual 

bench using the following tops:

2 x VRT

2 x VTBM/S/L

2 x OSR 24/20/18

(1.8 - 2.4m tops only)

1 x OLF 08 L

/OLF 06 L

1 x OILF 08

/OILF 06

1 x OLF 08 R

/OLF 06 R

4 mm Allen key

Equipment Required

(not included)

Fixings

(numbers based on a 2 unit bench)

4 x 5mm x 85mm 

hex bolts

2 x 5mm x 55mm 

hex bolts

4 x 5mm x 15mm 

hex bolts

Rubber mallet

To start with assemble the intermediate 

leg in its entirety; take the leg along with 

the wedge shaped spacers and two 

55mm bolts. Insert the bolts up though 

the holes in the leg frame and into the 

threaded holes on the underside of 

the spacers. Tighten them so they are 

secure but do not over-tighten. You 

should not have to use excessive force 

to tighten the bolts adequately.

With the intermediate leg assembled, 

take one of the beams and insert into 

the leg’s bracket as shown by slotting in 

and sliding down. The gap in the beam 

should face towards the rear of the 

desk i.e. the side which it is nearest to.

2 x VWT L/R

or

20 x 6mm x 26mm 

mush head screws 

(1.8 - 2.4m tops)

Содержание Oblique Visual OVRT 0806

Страница 1: ...let To start with assemble the intermediate leg in its entirety take the leg along with the wedge shaped spacers and two 55mm bolts Insert the bolts up though the holes in the leg frame and into the threaded holes on the underside of the spacers Tighten them so they are secure but do not over tighten You should not have to use excessive force to tighten the bolts adequately With the intermediate l...

Страница 2: ...with as many sections as your bench consists of With the bracket in the centre of each beam loosened adjust each frame to roughly fit the width of each top using a tape measure or top placed in front on the frame to check the width The tops will extend to the centre of each intermediate leg Using the mallet secure the end of the beam fully into the intermediate leg by tapping at the end so as not ...

Страница 3: ...pplied with the legs two with each leg and place one over each of the holes in the leg frame aligning the holes in each spacer roughly with the corresponding hole in the leg The spacer has a small lip which should fit over the radius on the edge of the leg Note this step is only for desks with a support rail only i e OVRD 1808 2008 2408 With the desk top turned upside down align the support rail w...

Страница 4: ...g by placing them through the holes in the wedge shaped spacers and into the underside of the desk top Fully tighten these bolts Now insert one of the 5mm x 85mm bolts through the bottom of the end leg frame and the spacer into the bottom of the desk top You may need to shift the leg slightly in order to get the bolt through and into the desk top Screw in far enough that the bolt holds itself in p...

Отзывы:

Нет отзывов