Venture Products Ventrac SS575 Скачать руководство пользователя страница 19

Страница: 19 / 53

SPREADER SETUP & INSTALL KITS

Setup - 19

1. Disconnect the negative battery cable from the

power unit’s battery.

2. Open the toolbox lid and remove the left (A) and

right (B) toolbox liner panels.

Place the wire adapter harness in the power

units seat box area. Route the ground wire with

the ring terminal along the main harness and

connect to the ground stud (C). Use zip ties (D)

to fasten the wire to the main harness.

4. Route the red and white wires with terminals into

the toolbox area.

5. Use a needle nose pliers to remove the green

plugs (E) from positions A1 and A3 (F - red high-

lighted positions) on the rear fuse panel.

NOTE: Both the picture

and the sketch are shown

from the rear of the fuse

panel inside the toolbox.

AA A B C D

87a

Back View Of Rear Fuse Block

Install the terminal on the red wire into position

A1 in the fuse panel. Install the terminal on the

white wire into position A3 in the fuse panel.

NOTE: the terminal can only be installed one

way. Orient the terminal with the hole pointing up

and insert into the fuse panel. The terminal needs

to snap into place. If necessary, use a needle

nose pliers to push the terminal in, being careful

not to damage the wire insulation. Double check

the connection by tugging gently on the wire with

your hand.

7. Reinstall the left and right toolbox liner panels.

Document Number

Kit Number / Part Number

Model

Serial Number Range

09.700169

70.8129

SS575

All Units

Tools Required:

3/8” wrench

7/16” wrench*

9/16” socket*

3/4” socket

impact driver

5/32” hex wrench*

Phillips screwdriver* side cut pliers

Before making repairs or adjustments set the parking

brake, turn off engine, and remove ignition key.

Always disconnect the negative battery cable from the

battery when working with electrical components. Always

work in a manner that does not put safety at risk!

Safety glasses must be worn during installation.
Ear (hearing) protection must be worn when us-

Installation Time (estimated)

1 hour

Installation Notes:

Right and left hand orienta

tion referred to in these instructions is determined

as if sitting on the tractor seat, facing forwards.

*Not necessary for all setup configurations.

SS575 Install 4500 Kit

Содержание Ventrac SS575






















































Результаты поиска

Содержание Ventrac SS575

Отзывы:

Бренды по названию

Популярные бренды

Venture Products Ventrac SS575, Руководство оператора и чертежи запасных частей

Результаты поиска

Содержание Ventrac SS575

Отзывы:

Бренды по названию

Популярные бренды