background image

9

www.ventilation-system.com

CONNECTION TO POWER MAINS

POWER OFF THE POWER SUPPLY PRIOR TO ANY OPERATIONS WITH THE UNIT.

THE UNIT MUST BE CONNECTED TO POWER SUPPLY BY A QUALIFIED ELECTRICIAN.

THE RATED ELECTRICAL PARAMETERS OF THE UNIT ARE GIVEN ON THE 

MANUFACTURER’S LABEL.

ANY TAMPERING WITH THE INTERNAL CONNECTIONS IS PROHIBITED  

AND WILL VOID THE WARRANTY.

Any tampering with the internal connections is prohibited and will void the warranty.
The fan is rated for connection to single-phase AC 220-240 V/50 Hz power mains. The connection must be made using durable, insulated 
and heat-resistant conductors (cables, wires). The actual wire cross section selection must be based on the maximum load current, 
maximum conductor temperature depending on the wire type, insulation, length and installation method.
The fan connection shall be made on the terminal block mounted inside the terminal box in strict accordance with the wiring diagram 
and terminal designations.

High — high speed
Med — medium speed
Low — low speed
N — neutral
L — line

 

 — grounding

S — ON\OFF switch
S1 — switch
QF — automatic circuit breaker
R1 — internal speed controller
SW — DIP switch

WIRING DIAGRAM

S

N

L

High speed

N

Low

Med

High

~220-240V

X

 

 

S

N

L

Low speed

N

~220-240V

X

 

 

Low

Med

High

S

N

L

Medium speed

~220-240V

X

 

 

Low

Med

High

N

S

N

L

High-Med-Low speed

N

~220-240V

X

 

Low

Med

High

S1

Boost ...

L

N

L

~220-240V

 

N

X1

SW

R1

QF

L

N

L

~220-240V

 

N

X1

Boost ... V

Boost ... EC

Содержание Boost 355

















Отзывы: