Vendors Exchange REVISION Скачать руководство пользователя страница 3

Страница: 3 / 28

INSTALLATION GUIDE

REVISION™ Door for National 157/167 - 158/168

PRECAUTIONARY STATEMENTS

WHAT THE SYMBOLS MEAN

WARNING, CAUTION,

and

NOTICE

statements are used in this installation manual to stress important

and critical information to safely service this door. These statements, according to the American National

Standards (ANSI), are described below.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING

THE CURVE DOOR. IF YOU NEED ANY ASSISTANCE, CALL 1-800-321-2311

THIS SYMBOL INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD

RESULT IN DEATH OR SERIOUS INJURY.

THIS SYMBOL INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD

RESULT IN MINOR OR MODERATE INJURY.

THIS STATEMENT IS USED TO ADDRESS PRACTICES NOT RELATED TO PHYSICAL INJURIES

OR SITUATIONS THAT WILL NOT CAUSE HARM.

NOTICE

WARNING

CAUTION

Overview

To TOC

Содержание REVISION





























Результаты поиска

Содержание REVISION

Отзывы:

Похожие инструкции для REVISION

Бренды по названию

Популярные бренды

Vendors Exchange REVISION, Руководство по установке

Результаты поиска

Содержание REVISION

Отзывы:

Похожие инструкции для REVISION

Бренды по названию

Популярные бренды