Vemco Ascent AR2 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 59

background image

VEMCO – ASCENT–AR / AR2 Manual

28 July

2018

4

2

Getting Started

After the ASCENT-AR has been removed from the packaging and inspected for any damage that may have
occurred during shipping, power and test the unit to ensure you can communicate with the release and it is
working properly. The ASCENT-AR was shipped with the batteries
installed but NOT connected.

2.1

Connect Battery

ASCENT-AR

is shipped with

the battery installed but

NOT connected

.

Open the

ASCENT-AR

case as described

in section

. You’ll find two batteries

in the Metal Internal Casing. The smaller
battery operates the release motor and is
already connected. The D or DD-cell
Lithium battery powers all other
operations in the

ASCENT-AR

and is

usually shipped unconnected within the
release.

STEP 1

Position the release so you can
see the Status Light.

Connect the two battery connector
halves together until a “click” is
heard and the

ASCENT-AR

release

’s light begins flashing.

Watch for a long green light to indicate the self-tests
were successful. If you see the long red light followed
by more flashes, then contact VEMCO for instructions.

STEP 2

Close the release case by following the instructions in section 5.1.4

STEP 3

WARNING

Do not over-tighten the case
pieces together or they may
be damaged.

«
...
9
10
11
12
13
...
»

Содержание Ascent AR2




























































Отзывы:

Нет отзывов

Похожие инструкции для Ascent AR2

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Бренд: ubbink Страницы: 30

Бренд: Wassermann Страницы: 24

Бренд: Ekinex Страницы: 37

Бренд: HMS Страницы: 36

Бренд: PMK Страницы: 24

Бренд: SteelFlex Страницы: 13

Бренд: Eaton Страницы: 38

Бренд: Bison Страницы: 4

DriveRack VENU360

Бренд: Harman Страницы: 4

Бренд: Kalamazoo Страницы: 4

Бренд: Detecto Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды