Velatia ORMAZABAL gae.630 Скачать руководство пользователя страница 57

Страница: 57 / 64

IG-322-EN version 03; 22/07/2022

General instructions

-insulated circuit-breaker panel:

Type

gae

.630 -1LSV(G)-/5/

in modular extensible design up to 24 kV, 20 kA

Maintenance

7.3. Fault clearance on the vacuum circuit-breaker

Fault

Possible cause(s)

Remedial action

1. Shunt release does not trip

•  No voltage
•  Voltage level too low
•  With DC releases, polarity reversed
•  Release defective
•  Impulse duration too short

• Check supply lines and plug-in connections

(refer to circuit diagram)

•  Check the voltage source
•  Contact the manufacturer
•  Observe the impulse duration

2. Undervoltage release does not trip

• See item 1

3. Motor winder does not tension

•  No voltage
•  Voltage level too low
•  Motor defective

• See item 1

4. Switch switches OFF immediately

after being switched ON

• Permanent “OFF” signal present
• Undervoltage release not activated, if fitted

• See item 1

5. Switch can not be switched ON

mechanically

• If key lock is fitted
• Electrical closing lock-out activated

• Unlock
• Check electrical closing lock-out activated

6. Switch can neither be switched ON

mechanically nor electrically

• Electrical closing lock-out not activated

• Apply a supply voltage
• See item 1

Table 7.1.

7.4. Return of switchgear

For an

Ormazabal

switchgear, an operating time of many

years is assumed. The “sealed pressure system” according to

IEC does not require refilling of the SF

-gas over the entire

operating time. Due to the high reliability of the switchgear,

arc faults are almost completely ruled out.

When handling a failed or disused switchgear, the national

health and safety guidelines must be observed.

The switchgear contains the fluorinated greenhouse gas

with 22.8t CO

equivalent, which is covered by EU

regulation 517/2014. SF

must be recovered and cannot be

released into the atmosphere.

When handling SF

, observe the standard IEC 62271-4.

All materials of this switchgear should be sent for recycling.

As a competent partner

Ormazabal

offers you the return of

your switchgear after the expiration of the operating time.

Here all necessary guidelines will be observed. The costs

involved depend on the legal requirements applicable at

the time of return.

Содержание ORMAZABAL gae.630

































































Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы:

Velatia ORMAZABAL gae.630, Руководство пользователя, Страница: 57 / 64

Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы: