Velatia ORMAZABAL gae.630 Скачать руководство пользователя страница 11

Страница: 11 / 64

IG-322-EN version 03; 22/07/2022

General instructions

-insulated circuit-breaker panel:

Type

gae

.630 -1LSV(G)-/5/

in modular extensible design up to 24 kV, 20 kA

Safety regulations

2.3.1. Operation

When operating the circuit-breaker panel the responsibilities

must be clearly defined and observed, so that no unclear

areas of responsibility in relation to safety arise.

Before commissioning the circuit- breaker panel and after

service work or modifications the circuit-breaker panel

must be inspected by qualified personnel for safe working

condition.

Before commissioning, all personnel in the danger zone

around the circuit-breaker panel must be warned and asked

to leave this area. There must not be any objects blocking

the access to the controls.

The user must operate the circuit- breaker panel only in

perfect condition.

Any changes that degrade safety must be reported

immediately to the supervisor.

Changes to the circuit-breaker panel are only permitted in

coordination with

Ormazabal

and under the supervision of

expert personnel.

Specialist personnel are persons who, due to their

professional training and experience, have sufficient

knowledge in the field of electrical technology and are

familiar with the applicable health and safety regulations

(DGUV Prescription 3 (previously BGV A3)), directives and

the generally accepted technical rules and regulations

(e. g. VDE-regulations, IEC-standards, DIN-standards).

2.3.2. Safety features

Safety features must not be altered, dismantled or rendered

ineffective. Unprotected parts of the system can cause fatal

injuries.

All safety installations, e. g. shrouds, must always be fully

functional and correctly in place. Operation of circuit-

breaker panel with faulty safety features is not allowed.

2.3.3. Auxiliary device for operation, maintenance and repair

If any auxiliary devices (tools or similar) are required for

operation, maintenance or repair of the circuit-breaker

panel, these must be in safe condition and should be used

in a safe way.

Any unnecessary and endangering use of auxiliary devices

of any kind on the circuit-breaker panel is not permitted.

2.3.4. Statutory health and safety instructions

Apart from these notes on prevention of accidents and the

notes attached to the circuit-breaker panel the locally valid

accident prevention instructions must also be observed.

2.3.5. Personal Protective Equipment (PPE)

To achieve the best possible protection for persons, we

recommend wearing personal protective equipment. This

applies for work on the switchgear as well as for switchgear

operation.

For the selection of personal protective equipment,

the national regulations of appropriate authorities and

professional associations must be complied with.

Содержание ORMAZABAL gae.630

































































Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы:

Velatia ORMAZABAL gae.630, Руководство пользователя, Страница: 11 / 64

Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы: