Veit SG67 Скачать руководство пользователя

Страница: 21 / 87

3.4.1 Performing the checks

Visual inspection for damage

Function check: When the ball valve is in the closed position, it

must be locked automatically by the locking strap.

Visual inspection for damage

Function check by means of “cracking open”

Set the steam generator to its operating pressure.

Turn the knurled nut (1) counter-clockwise until steam

escapes from the valve.

WARNING!
Risk of burns

–

At the safety valve

–

From escaping steam

Wear safety gloves to avoid burns.

Tighten the knurled nut again after 4-5 seconds.

NOTICE!

Only hand tighten the knurled nut. Do not use

tool, such as water pump pliers, for example.

CAUTION!
Leaks on the safety valve

If the safety valve is leaking:

–

Check if the knurled screw has been tightened

properly by hand.

–

If this does not remove the leaks, repeat the

“crack open” procedure as described above

2-3 times. Accumulation of dirt might be the

cause for the leak.

–

If the leaks on the valve can still no be

removed, the valve must be replaced.

Visual inspection for damage and secure installation

Locking strap for ball valve (Pos. 1)

Safety valve (Pos. 2)

“Crack open” procedure

Fig. 6: Knurled nut of safety valve

Temperature limiter (Pos. 3)

Safety

Built-in safety devices > Performing the checks

30.09.2022

Steam generator VEIT SG67

Содержание SG67
























































































Результаты поиска

Содержание SG67

Отзывы:

Похожие инструкции для SG67

Бренды по названию

Популярные бренды

Veit SG67, Руководство по эксплуатации

Результаты поиска

Содержание SG67

Отзывы:

Похожие инструкции для SG67

Бренды по названию

Популярные бренды